What to do if my Stanley SXUP1000XWE motor is not running?
If your Stanley Water Pump's motor isn't running, here's what to check: * Ensure the mains voltage is adequate and the plug (A12) is securely connected. * Reset the residual current device; if it trips again, consult an electrician. * Free the impeller from any obstructions. * If the motor or capacitor is damaged, contact your dealer.
Why is my Stanley SXUP1000XWE delivering only a small amount of water?
If your Stanley Water Pump is only delivering a small amount of water, consider the following: * Clean the suction strainer (A1) as it might be partially blocked. * Check for any obstructions in the hose and remove them. * Ensure you are using hoses of at least ø 25 mm (1”). * Keep in mind that an excessive head (height) will reduce the flow rate.
What to do if Stanley SXUP1000XWE Water Pump motor runs but no water is pumped?
If your Stanley Water Pump motor runs but doesn't pump water: * Clean the suction strainer (A1), as it may be clogged. * If installed, check the valve for jamming; clean or replace it. * Tilt the pump underwater to release any air bubbles from the pump body (A4).
Why does my Stanley SXUP1000XWE have an uneven operation?
If your Stanley Water Pump is operating unevenly: * Remove any solids obstructing the impeller's free rotation. * Ensure the liquid temperature does not exceed 35°C. * Connect the pump to an electrical system meeting the nameplate requirements. * Check the water level in the well; it might be too low or not flowing in fast enough. * If the motor is faulty, contact your dealer.
What to do if the thermostat is cutting out my Stanley Water Pump?
If the thermostat is cutting out your Stanley Water Pump: * Clean the inside of the pump body (A4) by directing a jet of water in through the delivery fitting (A2), allow the thermostat to cool for about 1 hour, and if needed, have the appliance checked by the Service Centre. * Check the water level in the well. Reduce the pump's flow rate by adjusting the connected users. Note: reducing the flow rate by more than 50% can damage the pump.
How to stop my Stanley Water Pump from pumping sandy water?
If your Stanley Water Pump is pumping water containing sand: * Inspect the well and install a sand trap filter. * Raise the pump off the bottom of the well.
Explains meaning of safety symbols E1 (disposal) and E3 (household use).
General warnings and advice on safe usage and manufacturer liability.
Lists actions to avoid to prevent injury, explosion, electrocution, and short-circuit hazards.
Lists essential precautions for safe operation, electrical connection, and maintenance.
Explains the manual's purpose and importance for installation and use.
Details the product packaging and delivery contents.
Provides guidance on environmentally responsible disposal of packaging materials.
Describes the appliance's design for pumping clean water in specific household applications.
Lists forbidden uses and modifications that can void warranty and cause damage.
Instructions for connecting the delivery hose, including diameter recommendations and airtight sealing.
Procedure for bleeding air from the appliance after starting up.
Guidance on installing the pump in wells, including depth, rope attachment, and cooling considerations.
Important safety considerations for operation, including dry operation and water leaks.
Notes on initial setup and readiness for use after connecting the hose.
Steps for connecting the plug and starting the appliance safely.
Instructions for ensuring the pump is immersed and how to switch it off.
Explains how flow rates are affected by installation conditions and head.
Instructions for cleaning the appliance after use and dealing with dirt buildup.
General| Type | Submersible |
|---|---|
| Power | 1000 W |
| Max Flow Rate | 18000 L/h |
| Max Head | 9 m |
| Weight | 5.5 kg |
| Cord Length | 10 m |
| Power Source | Electric |
| Maximum Delivery Height | 9 m |
| Maximum Immersion Depth | 7 m |
| Maximum Grain Size | 35 mm |
| Voltage | 230 V |
| Warranty | 2 years |
To Next Page
