LCD Configuration Menu
General press ◄► keys to move the cursor or cycle through selectable options.
Operation press ▲▼ keys to traverse menu items or increase/decrease parameter value.
press ENTER key to confirm current action or go to the next level of menu.
press ESC key to return to the previous state.
Press ESC key for 5 seconds triggers the Factory Reset.
■
Settings
♦ Source press◄► keys to select source of input.
MX-100R HDMI only
MX-200 HDMI or HDMI/Audio or CVBS
MX-300 HDMI or CVBS or SDI
♦ Standard press◄► keys to select RF output in ATSC or J.83B QAM technique.
♦ RF Out Frequency To select output frequency from the existing channel plan:
press ► key to show channel plan. Current channel selected and its corresponding
frequency is shown in ‘CHxx xxxM’ format. press ▲▼ keys to go up or down
the channel plan. press ENTER to select channel frequency from channel plan.
To manually enter output frequency between 50MHz and 900MHz:
press ENTER to edit the output frequency manually. press ◄► keys to move
the cursor to numerical field, and press ▲▼ keys to increase/decrease its value.
♦ Major Ch(annel) press ENTER to edit major/minor channel number between 1 and 1023.
♦ Minor Ch(annel) press ◄► keys to move the cursor to numerical field, and press ▲▼ keys
to increase/decrease its value.
♦ Prog(ram) Name press ENTER to show soft keypad, press◄►▲▼to move cursor to position and
press ENTER to select alphanumerical character. Maximum 15 characters allowed.
♦ Audio (Format) press ◄► keys to select output audio format in AC3, AAC or MPEG-1 L2.
♦ Network press ENTER to go to IP Settings page.
♦ Advanced press ENTER to go to Advanced settings page.
♦ Theme press ◄► keys to select color theme of user interface in red, blue, green or
black.
■
IP Settings (MX-200 and MX-300 only)
♦ IP Addr(ess) press ENTER to edit IP address, Subnet Mask and (Default) Gateway.
♦ Subnet press ◄► to move cursor between fields and press ▲▼ keys to increase/decrease
♦ Gateway numerical values in xxx.xxx.xxx.xxx format.
■
Advanced Settings
♦ Bitrate Encoding bit rate between 200 and 2000 kbps.
♦ FHD Output
press ◄► keys to select full HD output in Interlace or Auto mode.
♦ Latency
press ◄► keys to select output latency in 100ms, 500ms or 1000ms.
♦ RF Atten(uation)
press ◄► keys to select output
attenuation between 0dB and 30dB.
Default output level is 40dBmV (100dBuV).
♦ PMT PID Program Map Table (PMT) Packet ID (PID) between 32 and 8190.
♦ Video PID Video Packet ID (PID) between 32 and 8190.
♦ Audio PID Audio Packet ID (PID) between 32 and 8190.
♦ PCR PID Program Clock Reference Packet ID (PID) between 32 and 8190.
♦ TS ID Transport Stream ID between 1 and 65535.
♦ Service ID Service Stream ID between 1 and 65535.
♦ Network ID Network ID between 1 and 65535.
♦ ON ID Organization Network ID between 1 and 65535.
♦ Service Provider
press ENTER to show soft keypad to edit Service Provider name and Network
♦ Network Name
name. press◄►▲▼ keys to move cursor to position and press ENTER to select
alphanumerical character. Maximum 15 characters allowed.
♦ Login Password
press◄► keys to enable or disable login password. press ▲▼ keys to edit
4-digit numerical password if login password is enabled.
♦ Factory Reset
press ENTER to confirm factory reset to restore all default settings.
3
MX-100R, MX-200 and MX-300 HD Modulator
To Next Page
Loading...