What to do if my Steamfast SF-370 won't heat up and the power switch light is off?
First, ensure the Steamfast Steam Cleaner is plugged into a working electrical outlet. If it is, check your household circuit breaker or ground fault interrupter and reset it if necessary, or replace the fuse. If problems persist, consult a licensed electrician.
What to do if my Steamfast SF-370 isn't heating up, but the power light is on?
If your Steamfast Steam Cleaner's power light is on but it's not heating up, the reservoir might be empty, so refill it. Mineral build-up could also be the issue. Please, also ensure you've allowed sufficient time for the unit to heat up before using.
Why is my Steamfast Steam Cleaner releasing too much water with the steam?
Excessive water in the steam from your Steamfast Steam Cleaner can be caused by a few things. There might be water condensation in the steam hose, so point the nozzle towards a sink, tub, or the ground and shake while pressing the steam trigger until the excess water is released. Also, overfilling the reservoir can interfere with steam production; drain some water out. Finally, the unit may not have reached full operating temperature; wait until the heating indicator light turns off before steaming.
How to prevent cloudy floors after using Steamfast Steam Cleaner?
If your floor surfaces appear cloudy or streaky after steaming with the Steamfast Steam Cleaner, it could be due to a dirty microfiber pad. Replace the microfiber pad with a clean one. Alternatively, hard water residue on the floor could be the culprit. Try switching to distilled or de-mineralized water.
How to keep accessories attached to my Steamfast Steam Cleaner?
If accessories aren't staying connected to your Steamfast Steam Cleaner, first check that they are properly installed. Also, a dirty Microfiber Pad may cause connection issues, so replace it with a clean one.
Why Steamfast SF-370 Steam Cleaner won't heat up?
Your Steamfast Steam Cleaner might not be heating up because it isn't properly plugged into an electrical outlet. Another potential reason is that the household circuit breaker or ground fault interrupter has tripped, or a fuse has blown. You should reset the breaker or replace the fuse. If the switch still does not illuminate, cease usage immediately, unplug the unit, and contact Consumer Service for assistance.
What to do if Steamfast SF-370 has excessive water in steam?
If your Steamfast Steam Cleaner is producing excessive water in the steam, there are a few possible causes. First, there might be water condensation in the steam hose. To resolve this, point the nozzle towards a sink, tub, or the ground and shake it while pressing the steam trigger until the excess water is released. Also, ensure that you are not overfilling the boiler; filling it with more than 48 oz (1,420 ml) of water can interfere with steam production. Drain some water out of the boiler, and always use the included measuring cup to fill it with the correct amount of water. Finally, make sure the unit has heated to its full operating temperature by waiting until the heating indicator light turns off before you begin steaming.
What to do if Steamfast Steam Cleaner doesn't heat up but the light is on?
If your Steamfast Steam Cleaner's On/Off switch illuminates but the unit fails to heat up, it could be due to several reasons. The boiler might be empty, so you should refer to the Filling Boiler procedure. Another possibility is mineral build-up in the unit, requiring you to refer to the Care & Maintenance section. If neither of these resolves the issue, the unit may be damaged and require you to cease usage immediately, unplug it, and contact Consumer Service for further assistance.
Why is Steamfast SF-370 steam output weak?
If the steam output from your Steamfast Steam Cleaner is weak or intermittent, it could be due to a low water level in the boiler. Try refilling the boiler. It may also be caused by mineral build-up in the unit, so please refer to the Care & Maintenance section for details.
Why is the steam output weak on my Steamfast SF-370 Steam Cleaner?
A weak or intermittent steam output from your Steamfast Steam Cleaner is often due to a low water level in the reservoir. Another potential cause is mineral build-up within the unit.
Instructions for connecting steam mopping accessories like extension wands and mop head.
Step-by-step instructions for filling the steam cleaner's boiler with water.
Instructions for operating the steam cleaner for general cleaning tasks.
Instructions for using the steam cleaner for mopping floors.
General| Model Number | SF-370 |
|---|---|
| Type | Steam Cleaner |
| Heat-up Time | 8 minutes |
| Steam Time | 45 minutes |
| Power | 1500 W |
| Steam Pressure | 50 PSI |
| Accessories | Jet Nozzle, Corner Nozzle, Fabric Steamer, Brush Nozzle, Scrub Tool, Squeegee, Extension Wands (2) |
| Hose Length | 6 ft |
| Water Tank Capacity | 48 oz |
To Next Page