z RANDOM PLAY MODE (BY REMOTE CONTROL)
Pressing the RANDOM button on the remote control (17) will activate the Shuffle Play function and the Random
indicator “ RAN “ will show on the LCD Display.
Press the CD
I Play button (10 or 17 on the RC) to start playing the CD tracks in any order.
CD DISC PROGRAMMING IN CD
I
Up to 20 tracks on a CD can be programmed to play in any order. Before programming, make sure the system is in
Stop Mode, i.e. the CD is not playing:
1. Select “CD
I /AUX “ function but stop CD I playback.
2. Press the “CD
I Program” button (13), “ MEM “ will flash on the LCD display (2).
3. Select a desired track by pressing the Skip
or buttons (12).
4. Press the “ CD
I Program ” button (13) again to store the track into memory.
5. Repeat steps 3 and 4 to enter any additional tracks into memory.
6. When all the desired tracks have been programmed, press the CD
I “ Play/Pause ” button (10) to play the
disc in the designated order.
7. To cancel the programmed files, press the “ Stop
” button above CD I once, until the program indicator
“ MEM“ has disappeared from the display. Please note a programmed disc can only be played once.
IMPORTANT:
- If you wish to change to a different disc, always press the CD I “ Stop ” button (11) first until the
original information shows on the Display. Then press the “ CD
I Door Open ” button (9) to remove the
disc and change to another one. Close the drawer.
- Before opening the CD doors of either CD
I or CD II Mode, ensure the system stays in CD “ Stop “ Mode, which
means all programming has been cancelled.
- You must close the CD door of either CD
I or CD II before switching to any other function.
- The reaction time of the functions of the CD
II burner is longer than that of the normal CD I player due to the
complexity of the system. Do not repeatedly press all the different function buttons one after another and within
a short time, as this may cause the system to malfunction. If this happens, please reset the system by
switching the unit off for a while and then re-starting it.
- The reading and playback time of a CD-R(W) disc varies from brand to brand. It depends on the compatibility of
the disc used.
RECORDING FUNCTION OF CD II
The main function of CD II is for recording from Phono, Tape or CD I/AUX. All the recorded tracks will be stored in
“ AUDIO-CD “ format. Before starting recording:
1. Press the CD
II function button (20).
2. Open the CD
II drawer by pressing “S“ (23) above CD II, “OPEN” will show on the display.
3.
Place a new blank CD-R or CD-RW disc (see Specifications for recommended brands of recordable CD) in the
CD
II tray, with the printed side facing up, and close the drawer.
4. The CD Burner will start reading the disc and then show “bUSY”, “ 000 00:00” and “NO TOC”, to show a
recordable blank disc is in the drawer. It will also show either “CD-R” or “CD-RW”, depending on which type of
disc is being used.
IMPORTANT NOTES:
• You can only record onto a disc if the LCD display shows the “NO TOC” indicator (“no table of contents”).
• A CD-R disc can be recorded on only once and cannot be erased (un-finalized) or re-recorded onto - this can
only be done on a CD-RW (re-writable) disc.
• The playback quality of either CD-R or CD-RW discs varies when played back on other Audio CD Players.
• It is not guaranteed all discs recorded on this system will play back on all other Audio CD Players.
• The revolving speed of the CD
II CD burner is higher than the normal CD I Player mechanism. Thus, some
mechanical noise or vibration of the unit cabinet may occur during operation. This is not a malfunction
of the system.
• Due to variances in the quality and compatibility of CD-R(W) discs that are on general sale, please change to
another brand (see Specifications) if you cannot record onto the one you are using, or if the performance is not
consistent.
E-5
To Next Page
Loading...