– 14 –
– 15 –
– Control dial set to
= night-time operation
(approx. 2
lux)
The control dial must be turned to
when
adjusting the detection zone and performing the
functional test in daylight.
Note:
When setting the detection zone,
it is recommended to
• select the shortest time.
• twilight setting.
Note:
After the LED floodlight switches OFF, it takes
approx. 1second before it is able to start detecting
movement again. The LED floodlight will only
switch ON in response to movement once this
period has elapsed.
Self-test
When putting the floodlight into operation, the elec-
tronic system carries out a self-test which lasts for
approx. 1 minute. Once this has been completed,
the sensor is active.
Reach setting / adjustment
The detection zone can be optimised to suit
requirements.
Film shroud (Fig.6.2)
The film shroud can be used for masking out any
number of lens segments to limit reach as required.
Inadvertent triggering is ruled out or the sensor
can be targeted to watch over danger spots.
(Fig.6.3 / 6.4 / 6.5)
• The shrouds can be cut along the grooved
vertical and horizontal divisions. (Fig.6.2).
• Detach ring cover.
• Clip in shrouds at the top of the sensor lens.
• Fitting the ring cover fixes the shrouds firmly in
place. (Fig.6.2)
Sensor unit
The sensor housing can also be turned through
±80° for precision targeting.
– Turning the sensor unit horizontally through
± 80°. (Fig.6.6)
Other information:
Floodlight adjustment range (Fig.6.7)
7. Operation
The LED floodlight is not suitable for burglar alarm
systems as it is not tamperproof in the manner pre-
scribed for such systems. Weather conditions may
aect the way the LED floodlight works. Strong
gusts of wind, snow, rain and hail may cause the
light to come ON when it is not wanted because
the sensor is unable to distinguish between sudden
changes in temperature and sources of heat.
8. Cleaning and Maintenance
Hazard from electrical power.
Contact between water and live parts can result in
electrical shock, burns or death.
• Only clean tool in a dry state.
Risk of damage to property!
Using the wrong detergent can damage the light.
• Clean unit with a moist cloth without detergent.
9. Troubleshooting
Unit without power.
– Fuse not switched ON or faulty.
• Switch ON fuse.
• Change faulty fuse.
– Break in wiring.
• Switch ON mains switch.
• Check wiring with voltage tester.
– Short circuit in mains power supply lead.
• Check connections.
Unit does not switch ON.
– Wrong twilight setting selected.
• Re-set brightness response threshold
– Mains switch OFF.
• Switch ON mains switch.
– Fuse not switched ON or faulty.
• Switch ON fuse.
• Change faulty fuse.
– Detection zone too small or incorrect.
• Check and adjust detection zone.
– Light source faulty.
• The light source cannot be changed. Com-
pletely replace unit.
Unit does not switch OFF.
– Continued movement within the detection zone.
• Check detection zone.
• If necessary, limit or change detection zone.
Unit switches ON when it should not
– Movement within the detection zone, e.g. from
animals, trees or cars.
• Check detection zone.
• If necessary, limit or change detection zone.
– Unit is moving as a result of gusts of wind or
precipitation.
• Mount unit on a firm surface.
10. Disposal
Electrical and electronic equipment, accessories
and packaging must be recycled in an environmen-
tally compatible manner.
Do not dispose of electrical and electronic
equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste
Electrical and Electronic Equipment and its imple-
mentation in national law, electrical and electronic
equipment no longer suitable for use must be
collected separately and recycled in an environ-
mentally compatible manner.
11. Manufacturer's warranty
This Steinel product has been manufactured with
utmost care, tested for proper operation and safe-
ty and then subjected to random sample inspec-
tion. Steinel guarantees that it is in perfect condi-
tion and proper working order. The warranty period
is 36months and starts on the date of sale to the
consumer. We will remedy defects caused by ma-
terial flaws or manufacturing faults. The warran-
ty will be met by repair or replacement of defec-
tive parts at our own discretion. The warranty shall
not cover damage to wear parts, damage or de-
fects caused by improper treatment or mainte-
nance. Further consequential damage to other ob-
jects shall be excluded.
Claims under the warranty will only be accepted
if the unit is sent fully assembled and well-packed
with a brief description of the fault, a receipt or in-
voice ( date of purchase and dealer's stamp ) to the
appropriate Service Centre.
Repair service:
If defects occur outside the warranty period or are
not covered by the warranty, ask your nearest ser-
vice station for the possibility of repair.
MANUFACTURER'S
1
3
5
YEAR
GB
WARRANTY
MANUFACTURER'S
YEAR
WARRANTY
GB
To Next Page
