To Next PageTo Next PageWhy my Stiga Brush Cutter engine does not start?
If your Stiga Brush Cutter engine won't start or stay running, it could be due to several reasons. You may be using an incorrect starting procedure, so double-check the instructions. A dirty spark plug or an incorrect electrode gap can also cause this issue, so inspect the spark plug. Also, a clogged air filter could be the culprit; in that case, you should clean or replace the filter.
What to do if my Stiga BC 636 starts but has little power?
If your Stiga Brush Cutter engine starts but lacks power, a likely cause is a clogged air filter. Try cleaning or replacing it to resolve the problem.
Why Stiga BC 636 Brush Cutter engine has no power under load?
If your Stiga Brush Cutter engine operates irregularly or lacks power under load, a dirty spark plug or an incorrect electrode gap could be the cause. Inspect the spark plug to resolve this.
How to fix a flooded Stiga BC 636 engine?
If your Stiga Brush Cutter engine is flooding, it might be because the starter knob was operated repeatedly with the starter inserted. To fix this, remove the spark plug and gently pull the starter rope knob to eliminate excess fuel. Then, dry the spark plug electrodes and reassemble them on the engine.
Why my Stiga BC 636 engine causes excessive fumes?
Excessive fumes from your Stiga Brush Cutter engine may be due to an incorrect composition of the fuel blend. Make sure you prepare the fuel blend according to the instructions.
What to do if my Stiga BC 636 Brush Cutter has unusual machine vibrations?
If your Stiga Brush Cutter has unusual vibrations, it could be due to damaged or loose parts. Stop the machine, disconnect the spark plug cable, and inspect for damage. Check for and tighten any loose parts.
What to do if my Stiga BC 636 has struck a foreign body?
If your Stiga Brush Cutter has struck a foreign body, it could result in damaged or loose parts. Stop the machine, disconnect the spark plug cable, and inspect for possible damage. Check for and tighten any loose parts.
General| Brand | Stiga |
|---|---|
| Model | BC 636 Series |
| Category | Brush Cutter |
| Language | English |
Explains how to interpret specific information and symbols within the manual for safety and operation.
Lists how figures and titles are referenced throughout the manual.
Explains how figures are numbered and components are marked.
Explains how chapters and paragraphs are titled and referenced.
Emphasizes becoming familiar with controls and proper machine use.
Covers essential checks and preparations before using the machine.
Details mandatory protective gear for safe operation.
Guidelines for preparing the work area and ensuring safety.
Critical safety warnings regarding fuel handling and storage.
Safety precautions to follow while operating the machine.
Proper handling and operational techniques for safe use.
Information on noise/vibration limits and health risks.
Outlines conditions and situations where the machine should not be used.
Guidelines for upkeep, storage, and moving the machine safely.
General advice on regular upkeep to ensure safety and performance.
Instructions for safely storing the machine, especially with fuel.
Recommendations for environmentally responsible use and disposal.
Overview of the machine's design and its intended purpose.
Details the specific applications and designed uses of the machine.
Lists prohibited uses that can cause damage or injury.
Explains the meaning of various safety symbols on the machine.
Information about the machine's identification label and its data.
Identifies and describes the primary parts of the machine.
Lists the parts included in the packaging for assembly.
Step-by-step guide on how to unpack the machine carefully.
Instructions for assembling the front and rear handles/grips.
Specific steps for assembling the front hand grip (Type I).
Instructions for fitting the handle bar (Type II) and controls.
Instructions for fitting the handle bar (Type III) and controls.
Guidance on choosing and matching cutting tools with their guards.
Steps for correctly attaching the protective guard to the cutting tool.
Detailed instructions for fitting the guard for specific cutting heads.
Specific instructions for fitting the guard when using a saw blade.
Procedures for attaching and detaching cutting tools like line heads and blades.
Step-by-step guide to install the nylon line cutting head.
Instructions on how to detach the nylon line cutting head.
Guide for installing various types of cutting blades.
Instructions for detaching various types of cutting blades.
Steps to connect the drive shaft tube to the engine and handle.
How to use the switch to start and stop the engine.
Adjusting the engine speed using the throttle lever.
Function and use of the throttle safety lever.
How to use the grip to start the engine manually.
Operation of the choke for cold engine starts.
How to use the primer button to aid engine starting.
Information displayed on the machine's screen regarding operation.
Steps to take before starting the machine, including harness adjustment.
Detailed guide on how to properly wear and adjust the harness.
Specific instructions for using the double strap harness.
Specific instructions for using the back-pack harness.
Essential safety checks to perform before and during operation.
A checklist of components to inspect for proper condition.
Steps to test machine functions after starting.
Step-by-step procedure for starting the engine.
Instructions for starting the engine when it is cold.
Instructions for starting the engine when it is already warm.
Guidance on how to use the machine for various cutting tasks.
Different methods for cutting various types of vegetation.
Techniques for using the nylon line head effectively.
Describes the scything motion for cutting grass.
Techniques for precise trimming and cutting.
Guide for installing various types of cutting blades.
Guidelines for using the saw blade safely and effectively.
How to adjust the cutting line length while working.
Additional tips for operating the machine efficiently and safely.
Instructions on how to properly stop the machine.
Steps to take after finishing operation, including cleaning.
General safety rules and information before performing maintenance.
How to mix petrol and oil for the 2-stroke engine.
Specifications for the type of petrol to use.
Specifications for the type of oil to use.
Step-by-step guide for mixing and storing the fuel blend.
Procedures and precautions for refuelling the machine.
Instructions for cleaning the machine after use.
Importance of checking and tightening fasteners for safety.
Steps for cleaning the air filter to ensure engine performance.
How to clean, check, and replace the spark plug.
General information on maintaining cutting tools.
Guidance on sharpening and balancing cutting blades.
Instructions on how to replace cutting blades.
Detailed steps for replacing the cutting line head.
Specific instructions for Type I line head replacement.
Specific instructions for Type II line head replacement.
How to sharpen the wire cutting blade.
Guidance on adjusting the engine's idle speed.
Information about the carburettor and performance issues.
How to lubricate the angle transmission unit.
How to lubricate the flexible drive shaft.
