To Next PageTo Next PageWhy are the battery LEDs flashing in sequence on my Stiga Lawn Mower?
If the battery LEDs are turning ON and OFF in sequence, it indicates a communication error between on-board electronic modules. Switch off the machine and repeat the starting procedure. If the problem persists, contact a Service Centre.
What to do if icon fig. 12.E stays on and the battery LEDs 4 and 5 flash on my Stiga SDST 98 Li 48 V1?
If the icon fig. 12.E stays on and the battery LEDs 4 and 5 flash on your Stiga Lawn Mower, it indicates a current overload on the cutting means due to heavy working conditions. Try reducing the travel speed or increasing the cutting height. It could also be due to obstructions hindering the rotation of the cutting means, in which case you should remove the obstructions. Another cause might be the cutting-means assembly being full of grass; clean the cutting-means assembly in this case.
What does it mean if icon fig. 12.E stays on and the battery LEDs 2 and 5 flash on my Stiga SDST 98 Li 48 V1?
If the icon fig. 12.E stays on and the battery LEDs 2 and 5 flash, it indicates a current overload from the battery. This could be due to excessive working conditions or a slope that is too steep. Reduce the travel speed and check the gradient of the terrain you are working on.
What to do if [Push-button panel Type I] The icon fig. 12.E stays on and the battery LEDs 1 , 2 and 4 flash [Push-button panel Type II] The icons fig. 12.E and fig. 12.N stay on and the battery LEDs 1, 2 and 4 flash on my Stiga Lawn Mower?
If the icon fig. 12.E stays on and the battery LEDs 1, 2 and 4 flash (or icons fig. 12.E and fig. 12.N stay on and the battery LEDs 1, 2 and 4 flash), it indicates overheating of the drive motor. This can be due to the drive motor being under strain, a slope that is too steep, or excessive mud on the wheels. Reduce the travel speed, check the gradient of the slope, and ensure the wheels are not blocked and clean them if necessary.
What to do if [Push-button panel Type I] The icon fig. 12.E stays on and the battery LEDs 1 , 2, 4 and 5 flash [Push-button panel Type II] The icons fig. 12.E and fig. 12.O stay on and the battery LEDs 1, 2, 4 and 5 flash on my Stiga SDST 98 Li 48 V1 Lawn Mower?
If the icon fig. 12.E stays on and the battery LEDs 1, 2, 4 and 5 flash (or icons fig. 12.E and fig. 12.O stay on and the battery LEDs 1, 2, 4 and 5 flash), it means the machine was started with the drive pedal not released (not in neutral position). Turn the machine off and repeat the starting procedure only after making sure that the drive pedal is in neutral (pedal released).
What to do when icons 13.E and 13.O are ON and battery LEDs 1, 2, 3, and 5 flash on a Stiga SDST 98 Li 48 V1 Lawn Mower?
When icons 13.E and 13.O remain ON and battery LEDs 1, 2, 3, and 5 flash, it means the drive engagement/disengagement lever is in the drive disengaged position. Check the position of the drive engagement/disengagement lever and, if necessary, return it to the drive engaged position. If the problem persists, contact a Service Centre.
What do flashing LEDs 1, 2, and 4 with icons 13.E and 13.O mean on my Stiga Lawn Mower?
When icons 13.E and 13.O remain ON and battery LEDs 1, 2, and 4 flash, it indicates the drive motor is over-temperature or under stress. This can be due to a steep slope or excessive mud on the wheels. Switch off the machine and wait for at least 5 minutes before repeating the starting procedure. Reduce forward speed and check the slope of the ground where you are working. Also, ensure the wheels are not blocked and clean them if needed.
What should I do if my Stiga SDST 98 Li 48 V1 starts with the drive pedal not released?
If your Stiga Lawn Mower starts with the drive pedal not released (not in neutral position), switch off the machine and repeat the starting procedure only after checking that the drive pedal is in the neutral position (pedal released).
What to do if my Stiga Lawn Mower has unusual vibrations?
If you notice unusual vibrations while using your Stiga Lawn Mower, it could be due to incorrectly balanced or loose cutting blades, loose parts, or possible damage. It is recommended to contact an authorized service center for verification, replacements, or repairs.
Why is my Stiga Lawn Mower not switching on?
The machine may not switch on due to a low battery. Charge the battery.
General| Model | SDST 98 Li 48 V1 |
|---|---|
| Power Source | Battery |
| Voltage | 48 V |
| Cutting Width | 98 cm |
| Bumper | Yes |
| Battery charger | Included |
| Transmission method | Hydrostatic |
| Traction | Rear-wheel drive |
| Headlights | LED |
Identifies the machine as a ride-on mower with a seated operator.
Mandatory safety instruction to read the entire manual before operating.
Warning about potential danger from ejected objects during operation.
Warning regarding the risk of the machine tipping over on slopes.
Warning about the danger posed by the rotating cutting blades.
Details the function of dashboard icons, LEDs, and indicators.
Detailed technical data for MPST 84 Li 48 models (V1/V2).
Detailed technical data for SDST 98 Li 48 models (V1/V2).
Detailed technical data for SDST 108 Li 48 model (V3).
Detailed technical data for MPST 98 Li 48 model (V3).
Clarifies the meaning and importance of safety symbols on the machine.
Lists unsafe ways to operate the machine to prevent hazards.
General description of the pushbutton interface and its layout.
Procedure for setting the grass cutting height.
How to activate and deactivate the cutting blades.
Safety feature for immediate machine stop in emergencies.
Essential checks and operations before starting to use the machine.
Step-by-step guide for performing essential safety checks.
Details how the machine's safety mechanisms function.
Step-by-step instructions for starting the machine correctly.
General guide to operating the machine's functions.
Detailed steps and considerations for mowing grass effectively.
Procedure for safely turning off the machine.
Instructions for properly charging the machine's battery.
Final safety checks to perform before beginning operation.
Instructions for driving the machine and changing gears.
Tasks to perform after using the machine, before storage.
Steps to set up the machine correctly before starting mowing.
Information on maintaining battery health and charging procedures.
Instructions for cleaning the overall machine.
Crucial safety advice before performing any maintenance tasks.
Work related to the maintenance of the cutting means assembly.
Overview of required maintenance tasks and their frequency.
Steps to diagnose and resolve issues when the machine won't power on.
Steps to diagnose and resolve problems causing uneven grass cutting.
