To Next Page
K
Kevin PriceSep 8, 2025
How to fix ball bearing of the clutch drum is damaged on Stihl FS 460?
- JJoann MartinSep 8, 2025
Replace ball bearing.
How to fix ball bearing of the clutch drum is damaged on Stihl FS 460?
Replace ball bearing.
What to do if my Stihl Brush Cutter engine runs rough and misfires?
If your Stihl Brush Cutter engine runs roughly, misfires, or experiences temporary power loss, the spark plug boot may be loose. Press the boot firmly onto the spark plug and fit a new spring if necessary.
Why won't the starter rope rewind on my Stihl FS 460?
If the starter rope does not rewind, heavy fouling or rust may be present on the rewind spring. Clean or replace the rewind spring.
What to do if irregular spark on Stihl FS 460 Brush Cutter?
Check proper functioning of lever for stop function/contact spring or slide control/microswitch and ignition module. If there is damaged insulation or interruption in the ignition lead or a short circuit wire, check the ignition lead/ignition module, and replace the ignition module if necessary. Check operation of spark plug, clean spark plug and replace if necessary. For versions with M-Tronic, carry out diagnosis.
How to fix pinion damaged or worn on Stihl FS 460?
Replace set of pinions on the drive side and non-drive side.
What to do if cutting attachment out of true on Stihl Brush Cutter?
Resharpen cutting attachment, replace if necessary.
What to do if screws of the clutch are loose on Stihl FS 460 Brush Cutter?
Tighten the screws. Replace the clutch if necessary and check the threaded holes on the flywheel, replacing the flywheel if needed.
How to fix broken tension springs of the clutch shoes on Stihl FS 460?
Replace tension springs.
What to do if metering diaphragm damaged or shrunk on Stihl FS 460 Brush Cutter?
Replace metering diaphragm.
Why does the drive tube assembly on my Stihl Brush Cutter get very warm?
If the drive tube assembly becomes very warm, the drive shaft may not be sufficiently lubricated. Lubricate the drive shaft along its entire length, ensuring the entire length of the flexible liner is lubricated.
Explains symbols indicating danger, serious injury, or death.
Explains warning signs found on the trimmer for user safety.
Safety measures for the work area, bystanders, and flammable materials.
Safe condition requirements for the brushcutter, deflector, and mowing head.
Detailed instructions and warnings for fuel mixture and safe refueling practices.
Explanation of kickout forces and safe handling procedures to prevent injury.
Details the meaning of specific warning symbols related to danger.
Criteria for ensuring the brushcutter is in a safe operating state.
Safety precautions to be observed during brushcutter operation.
Defines operator qualifications, responsibilities, and health requirements.
Safety considerations for cleaning, maintenance, and user-unserviceable repairs.
Lists essential personal protective equipment and clothing for safe operation.
Lists the necessary steps to prepare the brushcutter for use.
Detailed instructions on the correct gasoline and oil mixture ratio for the engine.
Safe procedures for refueling the brushcutter's fuel tank.
Step-by-step instructions for starting the engine under various conditions.
Details starting procedures for different engine conditions.
Instructions on how to safely stop the engine.
Guidance on proper grip and control for safe and effective operation.
Instructions for mowing with different cutting attachments.
Recommended timeframes for performing key maintenance tasks.
Lists common problems and their corresponding remedies.
General| Cutting Diameter | 480 mm |
|---|---|
| Idle Speed | 2, 800 rpm |
| Ignition System | Electronic |
| Carburetor | All-position diaphragm carburetor |
| Vibration Damping | Yes |
| Shaft Type | Straight |
| Fuel Capacity | 0.75 liters |
| Maximum Power Speed | 9500 rpm |
| Shaft Length | 1, 800 mm |
