Why won't the starter rope rewind on my Stihl Trimmer?
If the starter rope on your Stihl Trimmer does not rewind, it could be due to a very dirty or corroded rewind spring, so clean or replace the rewind spring. Another possible cause is insufficient spring tension, in that case check the rewind spring and increase the tension. Finally, the rewind spring might be broken, so install a new rewind spring.
What to do if starter rope is difficult to pull or rewinds very slowly on Stihl Trimmer?
If the starter rope on your Stihl Trimmer is difficult to pull or rewinds very slowly, the starter mechanism may be very dirty. Thoroughly clean the complete starter mechanism.
What to do if the starter rope can be pulled out almost without resistance on my Stihl FS 94 Trimmer?
If the starter rope on your Stihl Trimmer can be pulled out almost without resistance and the crankshaft does not turn, the pegs on the pawls may be broken or the pawls are worn, so replace the pawls. Another cause can be fatigued pawl springs, in that case fit new springs and check the pawls, replacing them if necessary.
How to fix a Stihl Trimmer starter rope that cannot be pulled out far enough?
If the starter rope on your Stihl Trimmer cannot be pulled out far enough, the spring may be overtensioned. Check the rewind spring and reduce the tension.
Why is my Stihl FS 94 making loud noises?
Loud noises from your Stihl Trimmer can be caused by several factors. A stretched clutch spring can cause loud noises, in this case you should replace the clutch spring. Another cause can be a damaged clutch drum bearing, which requires replacing the fan housing. Finally, loose clutch screws can also be the culprit; you should tighten the screws, and if necessary, replace the clutch and check the tapped holes in the flywheel, replacing the flywheel if needed.
What to do if my Stihl Trimmer working tool stops under full load?
If the working tool on your Stihl Trimmer stops under a full load, it could be due to badly worn clutch shoes. In this case, install a new clutch. Another potential cause is a badly worn clutch drum, so you should install a new clutch drum.
What to do if the working tool runs when the engine is idling on my Stihl FS 94?
If the working tool continues to run when the engine of your Stihl Trimmer is idling, it could be because the engine idle speed is too high, so you should readjust it with the idle speed screw LA. Alternatively, a stretched or broken clutch spring may be the cause, so replace the clutch spring, or install a new clutch.
Why is my Stihl Trimmer engine running roughly with misfires and temporary power loss?
If your Stihl Trimmer engine runs roughly, misfires, or experiences temporary power loss, check the spark plug boot to ensure it is firmly connected to the spark plug, and replace the spring if necessary. Also, a sooted or oil-smeared spark plug can cause these issues, so clean the spark plug or replace it if necessary.
General| Engine Displacement | 24.1 cc |
|---|---|
| Power Output | 0.9 kW (1.2 bhp) |
| Cutting Diameter | 420 mm (16.5 in) |
| Engine Type | 2-stroke |
| Shaft Type | Straight |
| Sound Power Level | 107 dB(A) |
| Fuel Capacity | 0.54 l (18.3 oz.) |
Explains symbols on the machine for operational guidance.
Describes how text and illustrations are used in the manual.
Details physical, mental, and clothing requirements for safe operation.
Covers general safety aspects related to the tool itself.
Provides instructions on how to safely carry the tool.
Explains the procedure and safety measures for refueling.
Identifies and explains the function of the machine's controls.
Step-by-step guide for starting the engine in various conditions.
Explains the procedure for safely stopping the engine.
Instructions for cleaning or replacing the air filter for optimal performance.
Covers removal, checking, and installation of the spark plug.
Proper procedures for storing the machine for short or long periods.
Instructions for using various mowing heads and adjusting nylon line.
Guidance on using and maintaining metal cutting blades.
Warnings and precautions related to kickback and blade safety.
Table showing compatible combinations of attachments, deflectors, handles, and harnesses.
Step-by-step instructions for mounting the loop handle.
Guidance on selecting and mounting the correct deflector.
Procedures for attaching mowing heads and metal cutting attachments.
Diagram and list identifying all major components of the machine.
Glossary of terms used throughout the manual.
Technical data including displacement, power, speed, and weight.
Details the warranty for emissions control systems under federal regulations.
Explains the emissions control warranty specific to California regulations.
Lists trademarks officially registered by STIHL.
Lists common law and product-line specific trademarks used by STIHL.
To Next Page
