Strobel-Parameter list (DC1200-AB611A)
Setting range
Unit
Preset at Mode 56
58-4
58-4F
170-22D
170-22FD
218D-TP-R
310D; 3100D
310D-R; 3100D-R
810
VEB100-1
VEB100-1F
VEB100-1RF
VEB100-2
VEB100-2F
VEB100-2RF
VEB100-3
VEB100-3F
VEB100-3RF
VEB100-4
VEB100-4F
VEB100-5
VEB100-5F
VEB100-7 Ausf. 1
VEB100-7 ab Ausf. 2
VEB100-7 ab Ausf. 3
Stand: 11.02.2019 - PT_AB611A_D
F-110 F-111 F-112 F-113 F-115 F-121 F-134 F-135 F-153 F-155 F-156 F-161
Positioning speed n1
Maximum speed
(setting range) n2-
Beginning backtack speed n4
End backtack speed n4
Softstart speed n6
Lower limit of the n-max
setting range
Softstart
OFF / ON
Festoon stitch backtack
OFF / ON
Holding force during
machine standstill
Control signal trimming device
OFF / ON
Switch-off delay, control signal
trimming device
Direction of rotation
of the motor
070
n2_
0200
0200
0070
0200
0
0
00
0
0000
0
min-1 min-1 min-1 min-1 min-1 min-1 ms
200 2200 0600 0600 0500 0200 0 1 05 1 0200 0
200 3200 0600 0500 0200 0 1 05 1 0200 0
200 3200 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 1300 0400 0400 0500 0200 0 1 05 1 0200 0
200 1300 0600 0500 0200 0 1 05 1 0200 0
100 0600 0200 0200 0250 0200 0 1 05 1 0200 0
100 0600 0200 0200 0250 0200 0 1 05 1 0200 0
200 0420 0200 0200 0200 0200 0 1 05 1 0200 0
200 1800 0600 0500 0200 0 1 05 1 0200 0
200
1800 0600 0500 0200 0 1 05 1 0200 0
200 1800 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 1800 0600 0500 0200 0 1 05 1 0200 0
200 1800 0600 0500 0200 0 1 05 1 0200 0
200 1800 0600 0500 0200 0 1 05 1 0200 0
200 1800 0600 0500 0200 0 1 05 1 0200 0
200 2200 0600
0500 0200 0 1 05 1 0200 0
200 2200 0600 0500 0200 0 1 05 1 0200 0
200 1800 0600 0500 0200 0 1 05 1 0200 0