Stryker Performance-LOAD - EMC Information

EEMMCC iinnffoorrmmaattiioonn
GGuuiiddaannccee aanndd mmaannuuffaaccttuurreerr’’ss ddeeccllaarraattiioonn -- eelleeccttrroommaaggnneettiicc eemmiissssiioonnss
PPeerrffoorrmmaannccee--LLOOAADD is intended for use in the electromagnetic environment specified below. The customer or the user
of PPeerrffoorrmmaannccee--LLOOAADD should assure that it is used in such an environment.
EEmmiissssiioonnss tteesstt
CCoommpplliiaannccee EElleeccttrroommaaggnneettiicc eennvviirroonnmmeenntt
RF Emissions
CISPR 11
Group 2
The PPeerrffoorrmmaannccee--LLOOAADD system must emit
electromagnetic energy in order to perform its
intended function. Nearby electronic
equipment may be affected.
RF Emissions
CISPR 11
Class A
The PPeerrffoorrmmaannccee--LLOOAADD system is suitable
for use in all establishments other than
domestic and those directly connected to the
public low-voltage power supply network that
supplies buildings used for domestic
purposes.
RReeccoommmmeennddeedd sseeppaarraattiioonnss ddiissttaanncceess bbeettwweeeenn ppoorrttaabbllee aanndd mmoobbiillee RRFF ccoommmmuunniiccaattiioonnss eeqquuiippmmeenntt aanndd
PPeerrffoorrmmaannccee--LLOOAADD
PPeerrffoorrmmaannccee--LLOOAADD is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of PPeerrffoorrmmaannccee--LLOOAADD can help prevent electromagnetic interferences by
maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and
PPeerrffoorrmmaannccee--LLOOAADD as recommended below, according to the maximum output power of the communications
equipment.
RRaatteedd mmaaxxiimmuumm oouuttppuutt
ppoowweerr ooff ttrraannssmmiitttteerr
WW
SSeeppaarraattiioonn ddiissttaannccee aaccccoorrddiinngg ttoo ffrreeqquueennccyy ooff ttrraannssmmiitttteerr
mm
115500 kkHHzz ttoo 8800 MMHHzz
dd==((11..22)) ((√√PP))
8800 MMHHzz ttoo 880000 MMHHzz
dd==((..1188)) ((√√PP))
880000 MMHHzz ttoo 22..55 GGHHzz
dd==((..3355)) ((√√PP))
0.01 0.12 0.035 0.07
0.1 0.38 0.11 0.22
1 1.2 0.35 0.7
10 3.8 1.1 2.2
100 12 3.5 7
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer. Note 1: At 80 MHz and 800 MHz,
the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people.
GGuuiiddaannccee aanndd mmaannuuffaaccttuurreerr’’ss ddeeccllaarraattiioonn -- eelleeccttrroommaaggnneettiicc iimmmmuunniittyy
PPeerrffoorrmmaannccee--LLOOAADD is suitable for use in the electromagnetic environment specified below. The customer or the user of
PPeerrffoorrmmaannccee--LLOOAADD should assure that it is used in such an environment.
IImmmmuunniittyy tteesstt
EENN//IIEECC 6600660011 tteesstt lleevveell
CCoommpplliiaannccee lleevveell
EElleeccttrroommaaggnneettiicc
eennvviirroonnmmeenntt--gguuiiddaannccee
EN 32 6392-009-001 Rev D.3