Stryker PneumoSure Service Manual

EN
DE
2007/09 www.stryker.com 1000-xxx-xxx Rev. A
Service Manual
Service Handbuch
Insufflator for Laparoscopy and Vessel Harvesting
PRELIMINARY
C
O
PY

Stryker PneumoSure Specifications

General

Gas Compatibility	CO2
Intended Use	Laparoscopic surgery
Usage	Operating room
Portability	Portable with handle
Display	Digital
Safety Features	alarms
Power	100-240 V, 50/60 Hz
Power Source	AC

Summary

1 Safety Instructions

3 Device Setup

3.3 Pneumo Sure Wiring Diagram

3.6 Opening the Device

4 Maintenance and Service Tasks

4.1 Safety Test

Procedure for conducting a safety test, including visual checks and electrical measurements.

4.6.1 Checking Gas Supply Connection/Gas Inlet Filter

Steps to inspect the gas supply connection and filter for blockages or soiling.

4.6.2 Checking the High Pressure Sensor

Procedure for verifying the function of the high pressure sensor.

4.6.3 Checking High Pressure Regulator at the HPU

Steps to check and adjust the high pressure regulator on the HPU.

4.6.4 Checking High Pressure Unit HPU for Leaks

Method for testing the High Pressure Unit (HPU) for gas leaks.

4.6.5 Checking the High Pressure Heating Unit

Procedure to check the functionality of the high pressure heating unit.

4.6.6 Checking High Pressure Safety Valve HSV at the HPU

Steps to check the high pressure safety valve for proper operation.

4.7 Mounting the Calibration Adapter

4.8 Testing the Low Pressure Unit LPU for Leaks

Procedure to test the Low Pressure Unit (LPU) for leaks using a calibration adapter.

4.9 Testing the Venting System and Overpressure Alarm

Procedure to test the venting system and overpressure alarm functions.

4.10 Testing the Occlusion Warning

Steps to test the occlusion warning system of the device.

4.11 Fluid Sensor Test

Procedure to test the functionality and alarm of the fluid sensor.

5 Service Menu

5.1 Service Menu Access

5.2 Service Menu Overview

5.3 Touch Display Calibration

5.4 Offset Calibration

5.5 LOW Pressure Calibration

Procedure to calibrate the low pressure settings of the device.

5.6 HIGH Pressure Calibration

Procedure to calibrate the high pressure settings of the device.

5.7 LPR Calibration

Steps to calibrate the Low Pressure Regulator (LPR) for accurate pressure control.

5.8 Flow Calibration

Procedure to calibrate the gas flow rate of the device.

5.9 LSV Calibration

Procedure to calibrate the Low Pressure Safety Valve (LSV) for safe operation.

5.10 12-hr Test

5.11 Resetting to Factory Defaults

6 Replacing Components and Modules

6.1 Uninstalling/Installing Gas Supply Connection

Step-by-step guide for removing and installing the gas supply connection.

6.2 Uninstalling/Installing High Pressure Unit HPU

Detailed instructions for replacing the High Pressure Unit (HPU).

6.2.1 Replacing the Heater/Temperature Sensor

6.3 Uninstalling/Installing Low Pressure Unit LPU

6.4 Uninstalling/Installing PPV Valve

6.5 Uninstalling/Installing Power Supply Unit

6.6 Uninstalling/Installing Mains Socket with Fuse Holder

6.7 Uninstalling/Installing Potential equalization MC-Plug

6.8 Uninstalling/Installing MIO/Board MIO LCD

6.9 Uninstalling/Installing BAM Board

6.10 Uninstalling/Installing NET Board/Power Switch

6.11 Uninstalling/Installing IFM Board/ SIDNE Interface

6.12 Uninstalling/Installing HPL Board

6.13 Uninstalling/Installing Fluid Sensor

6.14 Uninstalling/Installing Device Front

6.15 Uninstalling/Installing Tube Connection

6.16 Uninstalling/Installing Tube Detection

6.17 Uninstalling/Installing Snap Lock

6.18 Uninstalling/Installing Touch Display

8 Error and Warning Messages