Supermicro X11DPX-T - Page 61

61
Chapter 2: Installation
Watch Dog
JWD1 controls the Watch Dog function. Watch Dog is a monitor that can reboot the system
when a software application hangs. Jumping pins 1-2 will cause Watch Dog to reset the
system if an application hangs. Jumping pins 2-3 will generate a non-maskable interrupt
signal for the application that hangs. Watch Dog must also be enabled in BIOS. The default
setting is Reset.
Note: When Watch Dog is enabled, the user needs to write their own application
software to disable it.
Watch Dog
Jumper Settings
Jumper Setting Denition
Pins 1-2 Reset
Pins 2-3 NMI
Open Disabled
1. Watch Dog
2. CMOS Clear
COM1
LAN
CTRL
DESIGNED IN USA
X11DPX-T
REV:1.01A
I-SATA4~7 I-SATA0~3
FANC FAND
CPU2
CPU1
BIOS
LICENSE
JBT1
M.2 CONNECTOR
SAN MAC
MAC CODE
JF1
BAR CODE
IPMI CODE
VGA
USB 2/3
BT1
JNVI2C2
JNVI2C1
PCH
FANA
FAN2
FAN5
FAN1
P2-DIMMC1 P2-DIMMB1 P2-DIMMA1 P2-DIMMA2
P2-DIMMD2 P2-DIMMD1 P2-DIMME1
P2-DIMMF1
FAN6
P1-DIMMA2 P1-DIMMA1 P1-DIMMB1 P1-DIMMC1
JPWR1
JPWR2
JPWR3
JPI2C1
FAN4
LEDBMC
S-UM12
S-SATA0
S-SATA1
FANB
FAN3
JNCSI1
S-SGPIO
JSTBY1
JWD1
JSEN1
COM2
P1-DIMMF1 P1-DIMME1 P1-DIMMD1 P1-DIMMD2
SP1
USB8 (3.0)
JTPM1
JPWR4
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
ALWAYS POPULATE DIMMx1 FIRST
JUIDB1
(UID)
LED2
(UID-LED)
USB 6/7 (3.0)
JL1
LEDPWR
JSD1
JSD2
JIPMB1
JRK1
JPTG1
JPCIE11
(CPU2 SLOT11 PCI-E 3.0 x4 (IN x8))
JPME2
LAN 2 LAN 1
USB 0/1
IPMI_LAN
USB 4/5 (3.0)
BMC
JPCIE2
(CPU1 SLOT2 PCI-E 3.0 x16)
JPCIE1
(CPU1 SLOT1 PCI-E 3.0 x8)
JPCIE3
(CPU1 SLOT3 PCI-E 3.0 x8)
JPCIE6
(CPU2 SLOT6 PCI-E 3.0 x16)
JPCIE5
(CPU2 SLOT5 PCI-E 3.0 x8)
JPCIE7
(CPU1 SLOT7 PCI-E 3.0 x8)
JPCIE8
(CPU2 SLOT8 PCI-E 3.0 x16)
JPCIE4
(CPU1 SLOT4 PCI-E 3.0 x16)
JPCIE9
(CPU2 SLOT9 PCI-E 3.0 x8)
JPCIE10
(CPU2 SLOT10 PCI-E 3.0 x8)
1
2