Supermicro X11SPH-NCTPF - Page 54

54
Super X11SPH-NCTPF/-NCTF User's Manual
Power LED/Speaker
Pins 1-3 of JD1 are used for power LED indication, and pins 4-7 are for the speaker. Please
note that the speaker connector pins (4-7) are used with an external speaker. If you wish to
use the onboard speaker, you should close pins 6-7 with a cap. Refer to the tables below
for pin denitions.
PWR LED Connector
Pin Denitions
Pin# Signal
1 JD1_PIN1
2 FP_PWR_LED
3 FP_PWR_LED
Speaker Connector
Pin Denitions
Pin# Signal
4 P5V
5 Key
6 R_SPKPIN_N
7 R_SPKPIN
Overheat/Fan Fail LED Header
The JOH1 header is used to connect an LED indicator to provide warnings of chassis
overheating and fan failure. This LED will blink when a fan failure occurs. Refer to the tables
below for pin denitions.
Overheat LED header
Status
State Denition
Solid Overheat
Blinking Fan Fail
Overheat LED
Pin Denitions
Pin# Signal
1
Pull high to +3.3V
power through 330-ohm
resistor
2 OH Active
IPMI CODE
MAC CODE
SAS CODE
SAN MAC
X11SPH-NCTPF/-NCTF
REV:1.01
DESIGNED IN USA
1
1
1
1
1
1
1
1
1
Intel
C622
LSI
3008
Aspeed
AST2500
Inphi
CS4227
(-NCTPF)
Intel
X557
(-NCTF)
M.2 PCI-E 3.0 X4
DLE1
LEDSAS
JNVME1
JNVME2
JPWR1
JTPM1
JRK1
SP1
LEDBMC
JL1
JBT1
JSTBY1
JSD2
JPS1
JPME2 JWD1
JVRM1
JP4
JPG1
JIPMB1 JNVI2C1
FANB
FANA
FAN3FAN4 FAN2
FANC
CPU FAN1
FAN5
JD1
S-SGPIO1
JP2 JP3
S-SATA0
S-SATA1
JF1
JPWR2
JSD1
LEDPWR
USB2/3
I-SATA 4-7
I-SATA 0-3
L-SAS0-7
IPMI_LAN
COM2
USB11/12(3.0)
PCH SLOT2 PCI-E 3.0 X4(in x8)
CPU SLOT3 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X16
USB4/5
USB6/7
USB8(3.0)
UID-SW
UID-LED
JF1
ON PWR
PS
FAIL
RST
UID LED
1
NIC
2
NICHDD
LED
X
PWR LED
NMI
DIMMC1 DIMMA1 DIMMB1
VGA
DIMMA2
JLAN1: LAN3/4
(-NCTF)
SFP1: LAN1/2
(-NCTPF)
USB9/10(3.0)
DIMMD1 DIMMD2
CPU
DIMMF1 DIMME1
USB0/1
COM1
JPI2C1
JOH1
1
BT1
1
1. Power LED/Speaker Header
2. Overheat/Fan Fail LED
Header
2