Surecom SW-102 User Manual

Push [Blue bottoni for MENU
sw-i 02
Digital VHF/UHF 125-525MHz
Power & S.W.R. Meter
Model: SW-102 $
Max Power: 120W
VSWR: 1.00-19.99
Frequency Range: Cover:1 25MHz-525MHz
Power in: 5V (micro usb)
Frequency counter: + - 0.1KHz (+ 5%)
U-ion Battery: 3.7V U ion Battery
In lout Impedance: 50 0
Size without Socket: 70”7535 mm
(in and out) Interface: N(5L16) / S0239
Net Weight: 220g
Package
lx SW 102 meter
lx English Instructions
ix USB charger Cable
i LCD DIM (Back Light Time) 0-9 1 *~n is OFF. I mm to 9 mmns
2 POWER OFF 0-9 3 “0” is ON, 1 mm to 9 mins
3 Adjustment frequency counter -99 to +99 0 1=0.1KHz • -1 =-0.1 KHz
I AdjustVHFpoweroffset -99 to ÷99 0 “1”isuptol%,”-l”is downtol%
5 AdjustUHFpoweroffset -99 to +99 0 “1”isuptoI%,”-l”is downtol%
I AdjustVHFlowPoweroffset -99 to ÷99 0 “l”isuptol%,”-l”is downtol%
2, AdiustUHFlowPoweroffset -99 to ÷99 0 “1”isuptol%,”-1”is downtol%
“ Supplier, the product will add functionality without having to give notice
Sat & SAVE:
1. Press MENU [Blue bottonj
2. Press Fl [Red bottonflselect 1-7 Function)
3. Press [Blue bottonj ( -), [Yellow botton] (+)
4. Press the [Red botton jfor 2 seconds
5. Press the [Red botton 1 2 second and relest ,show the save and exit page
6. [Blue bottonj for save , [Yellow botton] not save and exit
Trouble shootino
1. No OperatIon?
-PLease charge with USB cable i-5V , or come with PSU -
-Push and hold on the “RED” botton -
-Replacement battery when battery dead. (below Ver 5.1 use by l4500battery,V1 .X use by li-ion
polymer battery.
-There are still problems with steps 1. and 2.and a, please contact service center.
How to Connect Radio:
TX: Connect to RADIO RF Output
ANT : Connect to ANTENNA or 50 OHM Dummy Load
How to charger:
Connect external USB 5V source
(e.g. USB charger) to micro USB input
When display is showing ‘E’, it means the unit is powered by USB.
When display is showing ‘B’, it means the unit is powered by internal battery.
How to check the SWR. of your Antenna:
Connect to “TX” on Radio output and Antenna to “ANT”. Proper adaptor/cable is required if your device
has different type of connectors.
flMeasurement V.S.WR.:
2)SW 102 TX connect Radio RF out
3)Radio TX, SW-i 02 with display S.W.R. measure data.
*[k not affect the test In the following cases, there are objects nearby and placed horizontally.
How to check the output Watt of your transceiver:
Connect to “TX” on Radio output and dummy Load to “ANT”. Proper adaptor/cable Is required if your
device has different type of connectors.
I )Measurement Power:
2)SW-i 02 TX connect Radio RF out
3)SW 102 ANT connect 50 ohm Dummy Load
4)Push Radio TX, SW 102 display is Power measure data.
*(SW1 02 is not for DMR system)
2.Watt ISWR read data Is not hold on ?
-Some Radio problem when end of TX
.Radio output TX is not stabilizing.
3.Read the watt data Is not accurate?
-SW-i 02 is not for DMR system
-Don’t not use the antenna get the watt data.
-Please use the correct power dummy load to measure (must be 50 OHM)
-The data read error when not read the frequency from radio
-The TX input is weak, Input Watt below 0.5W
4.Read the S.W.R. data Is not accurate?
-SW-i 02 is not for DMR system
-Do not affect the test in the following cases, there are objects nearby
-Do not affect the test in the following cases,piaced horizontally.
5. Read the Frequency counter Is not display or read frequency not accurate?
e.g. Radio is 145.000 ,read 145.003, SW-i 02 Is not for DMR system
-Input below 0.5W
Please use menu mode and fine tune the frequency offset.
6.Display have problem ? eg.BLack or Garbled or no Display
Restart the SW-i 02, Remove the inside battery.
-There are still problems with steps 1. and 2., please contact service center.
7. How to RESET the mirco chip
-Off mode ,Hoid the Red button and the display show “restore to default”
-There are stiii problems with steps 1. and 2., please remove the battery.
“All Specifications are subject to change without notice
Key SpecificatIons/SpecIal Features:
Detect S.W.R.
Measurement Power
Measurement Frequency counter
Soeciflcatlons:
USER’S MANUAL
CE
UP to V2.02
ix USB power Supply

Surecom SW-102 Specifications

General

Brand	Surecom
Model	SW-102
Category	Measuring Instruments
Language	English

Summary

SW-102 Meter Specifications and Features

Key Specifications and Features

Detect S.W.R., Measurement Power, and Measurement Frequency counter.

Detailed Device Specifications

Includes model, power, frequency range, battery, impedance, size, and interface details.

Package Contents

Lists the items included in the SW-102 meter package.

Connecting and Operating the SW-102 Meter

Connection Guide

Instructions on connecting the meter to a radio and antenna for testing.

Charging the Device

Guidance on how to charge the SW-102 meter using an external USB source.

Measuring S.W.R.

Steps to correctly measure the Standing Wave Ratio (S.W.R.) of your antenna.

Measuring Output Power

Instructions on how to measure the output power of your transceiver.

Menu Functions and Operation

Menu Item Descriptions

Details on menu functions like LCD dimming, power off, and frequency adjustments.

Setting and Saving Configuration

Procedure for navigating menu options, selecting functions, and saving settings.

Troubleshooting Common Issues

Trouble Shooting Guide

Solutions for common problems like no operation, inaccurate readings, and display issues.