EasyManua.ls Logo

Suzuki SMD9 - User Manual

Suzuki SMD9
43 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Installation Manual
IMPORTANT NOTICES AND SAFETY INSTRUCTIONS..........i
SYSTEM CONFIGURATION ....................................................iii
EQUIPMENT LIST ....................................................................iv
1. INSTALLATION....................................................................1
1.1 Disply Unit Installation............
......................................................
1
1.2 Radar Sensor (DRS4W) Installation............................................4
1.3 Transducer Installation................................................................5
1.4 Speed/Temperature Sensor (Option) Installation......................14
2. WIRING...............................................................................15
2.1 Power/NMEA0183 Port.............................................................15
2.2 XDR Port
.....................................................................................
16
2.3 NMEA2000 (CAN bus) Connections..........................................17
3. SETTINGS AND ADJUSTMENTS
.....................................
18
3.1 Starting the Setup Procedure
.....................................................
18
3.2 How to Use the Menu
................................................................
19
3.3 Initial Setup Menu
.......................................................................
20
3.4 How to Set up the SUZUKI Gateway.........................................24
3.5 SMD 7/9 Connection Examples of Various Systems
.................
28
3.6 How to Set Up the Fish Finder...................................................36
3.7 How to Set Up the Radar...........................................................37
4. INPUT/OUTPUT DATA........................................................39
4.1 How to access the [Interface] menu...........................................39
4.2 How to set up for NMEA0183 configurations .............................39
4.3 How to select a data source
.......................................................
39
4.4 How to select which NMEA2000 data to output
.........................
40
4.5 How to select which NMEA0183 sentence to output
.................
40
4.6 How to calibrate (offset) the sensors .........................................41
4.7 How to reset the [Interface] menu..............................................42
4.8 NMEA0183/NMEA2000 Monitor
.................................................
42
5. MAINTENANCE AND TROUBLESHOOTING ....................43
5.1 General Maintenance.................................................................44
5.2 Life of Parts................................................................................44
5.3 Troubleshooting .........................................................................44
5.4 How to Restore the Default Settings..........................................46
5.5 How to View the System Information .........................................46
APPENDIX 1 MENU TREE ..................................................AP-1
APPENDIX 2 RADIO REGULATORY
INFORMATION ......AP-9
SPECIFICATIONS ................................................................SP-1
OUTLINES ..............................................................................D-1
INTERCONNECTION..............................................................S-1
Multi-Function Display
Model
SMD7/SMD9
PACKING LISTS.....................................................................A-1

Table of Contents

Questions and Answers

  • C
    Christopher HodgeSep 8, 2025
    What to do if Suzuki Monitor TX screen appears momentarily?
    • J
      James MooreSep 9, 2025
      If you tap the [TX] icon to transmit on your Suzuki Monitor and the "TX screen" appears momentarily, but the radar soon goes into stand-by, the overload protection has activated. To restore normal operation, turn off all equipment in the network, wait a few seconds, then turn on all the equipment.
  • R
    Robert MillerAug 23, 2025
    What to do if Suzuki Monitor display has frozen?
    • C
      Cody SmithAug 23, 2025
      If the display of your Suzuki Monitor has frozen, try the following steps: 1. Push the power switch until the power goes off. 2. Turn the power on again. 3. Push the hard reset button, located below the microSD card slots.
  • C
    crystal50Aug 25, 2025
    What to do if Suzuki Monitor power is on but nothing appears on the screen?
    • M
      Maria CampbellAug 25, 2025
      If your Suzuki Monitor's power is on but nothing appears on the screen, try pressing the power button several times to adjust the brilliance. Also, check to ensure the unit is properly plugged into the power source.
  • M
    Michael TaylorAug 26, 2025
    What to do if Suzuki Monitor touch screen is not responding?
    • J
      Julie MendezAug 27, 2025
      If the touch screen on your Suzuki Monitor is not responding to touch operations: * Press the power key and check that [Touch Screen] in the [Brilliance] pop-up menu is set to [ON]. * Turn the power off, then on again. If the problem continues, contact your local dealer for assistance.
  • G
    Geoffrey JamesAug 27, 2025
    Why is Suzuki Monitor position not fixed?
    • J
      joseph02Aug 28, 2025
      If the position on your Suzuki Monitor is not fixed, check for interfering objects near the display unit that might be blocking reception.
  • J
    jamiebrownSep 22, 2025
    How to fix noise or interference on Suzuki Monitor display?
    • M
      Michael WrightSep 22, 2025
      To address noise or interference on your Suzuki Monitor display: * Ensure the transducer cable is not near the engine. * Check the ground for a tight connection and any corrosion. * See if another fish finder near your boat has the same frequency as your fish finder. * Try to reduce interference with [Interference] in the [Quick Set- tings] menu (cog-wheel at the bottom-left of the display).
  • S
    Susan RomeroSep 16, 2025
    What to do if Suzuki Monitor depth indication does not appear?
    • A
      Alicia RangelSep 16, 2025
      If the depth indication does not appear on the screen of your Suzuki Monitor, adjust the bottom level HF/LF.
  • E
    Erin BrooksSep 18, 2025
    How to display the seabed on Suzuki Monitor?
    • Q
      qcoxSep 18, 2025
      To display the seabed on your Suzuki Monitor, for manual operation, adjust the gain and range to display the bottom echo in reddish-brown.
  • K
    Krystal ColemanSep 7, 2025
    What to do if Suzuki Monitor marks and characters appear, but echoes do not appear?
    • N
      nicoleayalaSep 7, 2025
      If marks and characters appear on your Suzuki Monitor, but echoes do not appear, check if the radar source is correct.
  • T
    Teresa SimpsonSep 4, 2025
    What to do if Suzuki Monitor discrimination in range is poor?
    • K
      Kathleen DixonSep 4, 2025
      If you are experiencing poor discrimination in range on your Suzuki Monitor, adjust the rain control.

Summary

IMPORTANT NOTICES AND SAFETY INSTRUCTIONS

Safety Precautions

Warnings and cautions before operation.

SYSTEM CONFIGURATION

SPECIFICATIONS OF MULTI-FUNCTION DISPLAY SMD7;9

INSTALLATION

Transducer Installation

Transom mount transducer

How to mount a transducer inside the hull

WIRING

Power;NMEA0183 Port Connection

SETTINGS AND ADJUSTMENTS

Starting the Setup Procedure

How to Set Up the SUZUKI Gateway

Setting up the Suzuki Gateway.

How to Set Up the Fish Finder

Setting up fish finder.

How to Set Up the Radar

Setting up radar.

INPUT;OUTPUT DATA

How to calibrate (offset) the sensors

MAINTENANCE AND TROUBLESHOOTING

Troubleshooting

General troubleshooting steps.

How to Restore the Default Settings

SMD7;9 INTERCONNECTION (DIAGRAM)

Suzuki SMD9 Specifications

General IconGeneral
BrandSuzuki
ModelSMD9
CategoryMonitor
LanguageEnglish

Related product manuals