What to do if Suzuki Monitor TX screen appears momentarily?
If you tap the [TX] icon to transmit on your Suzuki Monitor and the "TX screen" appears momentarily, but the radar soon goes into stand-by, the overload protection has activated. To restore normal operation, turn off all equipment in the network, wait a few seconds, then turn on all the equipment.
What to do if Suzuki Monitor display has frozen?
If the display of your Suzuki Monitor has frozen, try the following steps: 1. Push the power switch until the power goes off. 2. Turn the power on again. 3. Push the hard reset button, located below the microSD card slots.
What to do if Suzuki Monitor power is on but nothing appears on the screen?
If your Suzuki Monitor's power is on but nothing appears on the screen, try pressing the power button several times to adjust the brilliance. Also, check to ensure the unit is properly plugged into the power source.
What to do if Suzuki Monitor touch screen is not responding?
If the touch screen on your Suzuki Monitor is not responding to touch operations: * Press the power key and check that [Touch Screen] in the [Brilliance] pop-up menu is set to [ON]. * Turn the power off, then on again. If the problem continues, contact your local dealer for assistance.
Why is Suzuki Monitor position not fixed?
If the position on your Suzuki Monitor is not fixed, check for interfering objects near the display unit that might be blocking reception.
How to fix noise or interference on Suzuki Monitor display?
To address noise or interference on your Suzuki Monitor display: * Ensure the transducer cable is not near the engine. * Check the ground for a tight connection and any corrosion. * See if another fish finder near your boat has the same frequency as your fish finder. * Try to reduce interference with [Interference] in the [Quick Set- tings] menu (cog-wheel at the bottom-left of the display).
What to do if Suzuki Monitor depth indication does not appear?
If the depth indication does not appear on the screen of your Suzuki Monitor, adjust the bottom level HF/LF.
How to display the seabed on Suzuki Monitor?
To display the seabed on your Suzuki Monitor, for manual operation, adjust the gain and range to display the bottom echo in reddish-brown.
What to do if Suzuki Monitor marks and characters appear, but echoes do not appear?
If marks and characters appear on your Suzuki Monitor, but echoes do not appear, check if the radar source is correct.
What to do if Suzuki Monitor discrimination in range is poor?
If you are experiencing poor discrimination in range on your Suzuki Monitor, adjust the rain control.
Covers manual usage, warranty, equipment operation, and manual retention.
Instructions for discarding the product and used batteries according to regulations.
Highlights warnings for electrical shock, water ingress, and handling the display unit.
Lists all parts included in the standard package for the display unit.
Lists additional accessories and components available for purchase.
Covers mounting the main display unit on a desktop or flush mount.
Instructions for installing the optional FURUNO DRS4W radar sensor.
Guidance for installing various types of transducers on the vessel.
Details for mounting transducers through the hull and on the transom.
Guidance for mounting transducers inside the hull and Triducer installation.
Installation instructions for ST-02MSB and ST-02PSB speed/temperature sensors.
Installation instructions for T-04MSB and T-04MTB temperature sensors.
Details on connecting NMEA0183 equipment and NMEA2000 CAN bus network.
Instructions for connecting the transducer to the XDR port.
Guides through the initial setup process upon first system power-on.
Explains how to navigate and use the system's menu interface.
Steps for setting up the SUZUKI Gateway and engine parameters.
Procedures for setting up the fish finder's initial parameters.
Guides for setting up the radar and aligning the antenna heading.
Accessing and configuring NMEA0183 and NMEA2000 sensor settings.
Selecting data sources and configuring NMEA output sentences/PGNs.
Calibrating sensors and resetting interface menu settings to defaults.
Routine checks for cables, display unit, and radar antenna for optimal condition.
Guides for resolving common problems like power, display, and touch screen issues.
Procedures to reset menu settings or all unit settings to factory defaults.
General| Resolution | 800 x 480 pixels |
|---|---|
| Aspect Ratio | 16:9 |
| Contrast Ratio | 500:1 |
| Response Time | 25ms |
| Screen Size | 7 inches |
| Input Voltage | 12 V DC |
| Power Consumption | 5 W |
| Operating Temperature | 50°C |
| Storage Temperature | -20°C ~ 60°C |
To Next Page
