Swing-N-Slide Olympus WS 5031 - User Manual

1
Specifi cations subject to change without notice.
Manufactured for: Swing-N-Slide® • 1212 Barberry Drive • Janesville, Wisconsin 53545 • USA • 1-800-888-1232 • www.swing-n-slide.com
Made in USA • Printed in USA
LDR 03-08-2019 LA 5940
Olympus Wave Slide Instructions
WS 5031,
WS 5032, WS 5033
x2
x22
x11
ASSEMBLY STEPS
1. Align slide sections and the backing plates together on
the ground (Fig. 1). Begin attaching two slide sections
together by securing the bolts in place fi nger tight (see
Fig. 2 for proper Bolt Sequence). Following this pattern
install (1) bolt, (2) washers and (1) lock-nut per hole
(see Fig. 1).
Once all (11) bolts, (22) fl at washers and (11) lock-nuts
are in place go back and tighten all hardware with
appropriate tools.
IMPORTANT: Tighten securely so backing plates
and slide sections are tight against each other AND
there are a minimum of one to two threads extending
beyond each lock-nut.
Fig. 1
Fig. 2
Not Included In Kit:
Fits 60” (152,4 cm) Deck Height
FOR PRIVATE USE ONLY
DO NOT USE IN PUBLIC SETTNGS!
Weight Limit: 250 lbs
For children 2-10 years of age
Tighten nut until washers are tight against backing plates.
(11) 5/16” (7,8 mm) Lock-nut
(11) 5/16” x 1”
(7,8 mm x 19 mm)
Hex Head Bolt
(22) 5/16” (7,8 mm)
Flat Washers
Backing Plates
Backing Plates
Stake
2” x 4” x 17” (5,1 x 10,2 x 43,1 cm)
Use Pressure-Treated Wood
1-3/4”
(4,4 cm)
17” (43,1 cm)
Cut
1-3/4” (4,4 cm)
Tape Measure
Hammer
1/8” & 1/4” Drill Bits
Phillips Bit
WARNING: Assembly by adult.
AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte.
ADVERTENCIA: El ensamblaje lo debe hacer un adulto.
WARNING: ASSEMBLY BY ADULT.
WARNING: ASSEMBLY BY ADULT
Circular Saw
Electric Drill
Socket Wrench set /
Wrenches
KIT INCLUDES:
x11
Hex Bolt
x2
1-1/4”
(3,2 cm)
Deck Screw
x4
1-1/4”
(3,2 cm)
1/4”
(6 mm)
1/2”
(12,7 mm)
Truss Screw
Tools Required:
Screw size should be a #8 thread size
minimum and coated for use
with treated wood.
Screw must be to sizes shown at a
minimum. Do not use a screw size
shorter than 1-1/4” (3,2 cm) long.
x1
1
5
3
6
7
9
10
11
2
4
8

Summary

Assembly Steps

Initial Slide Section Assembly and Tightening

Align slide sections with backing plates and securely tighten hardware, ensuring minimal thread extension.

Slide Placement and Ground Anchoring

Position slide, considering safety zones, and anchor it to the ground using a stake and deck screws.

Attaching Slide to Unit and Screw Management

Secure slide to the playset structure, check for protruding screws, and use slide blocks if necessary.

Safety Checklist and Installation

Installation Safety Checks

Verify adherence to assembly instructions, proper hardware tightening, and secure anchoring for safe installation.

Operating Safety Guidelines

Ensure adult supervision and warn children about safe usage practices to prevent injuries.

Safety Maintenance Schedule

Perform regular checks, lubrication, and tightening of hardware to maintain equipment safety.

Additional Required Safety Installation

Follow critical instructions for anchoring, shock-absorbing surfacing, and use zone requirements.

Manufacturers Limited Warranty

Warranty Coverage Details

Outlines limited warranties for slides, play set kits, and accessories against defects in workmanship and materials.

Exclusions and Limitations

Specifies conditions not covered by warranty, including misuse, unauthorized repairs, and cosmetic defects.

Swing-N-Slide Olympus WS 5031 Specifications

General

Product Name	Swing-N-Slide Olympus WS 5031
Category	Play Sets & Playground Equipment
Assembled Depth (in.)	120
Deck Height (in.)	48
Material	Wood
Color	Natural
Weight Capacity per swing	115
Number of Swings	2
Assembly Required	Yes
Swing Type	Belt
Warranty	1 year