Swing-N-Slide WS 5037 - User Manual

1
Specifi cations subject to change without notice.
Manufactured for: Backyard Play Systems • 166 Etowah Industrial Court • Canton, Georgia 30114 • USA • 1-800-882-0272 • playsupport@backyardproducts.com
Made in USA • Printed in USA
LDR 08-11-2021
LA 8163
ASSEMBLY STEPS
1. Align slide sections and the backing plates together on
the ground (Fig. 1). Begin attaching two slide sections
together by securing the bolts in place fi nger tight (see
Fig. 2 for proper Bolt Sequence). Following this pattern
install (1) bolt, (2) washers and (1) lock-nut per hole
(see Fig. 1).
Once all (11) bolts, (22) fl at washers and (11) lock-nuts
are in place go back and tighten all hardware with
appropriate tools.
IMPORTANT: Tighten securely so backing plates
and slide sections are tight against each other AND
there are a minimum of one to two threads extending
beyond each lock-nut.
Fig. 1
Fig. 2
Not Included In Kit:
Weight Limit: 200 lbs
For children 3-11 years of age
Tighten nut until washers are tight against backing plates.
(11) 5/16” (7,8 mm) Lock-nut
(11) 5/16” x 1”
(7,8 mm x 19 mm)
Hex Head Bolt
(22) 5/16” (7,8 mm)
Flat Washers
Backing Plates
Backing Plates
Stake
2” x 4” x 17” (5,1 x 10,2 x 43,1 cm)
Use Pressure-Treated Wood
1-3/4”
(4,4 cm)
17” (43,1 cm)
Cut
Circular Saw
Electric Drill
Tape Measure
Hammer
1/8” & 3/16” Drill Bits
Phillips Bit
2-Piece Cool Wave Slide Instructions
WS 5037,
WS 5038, WS 5039
Fits 48” (121,9 cm) Deck Height
FOR PRIVATE USE ONLY
DO NOT USE IN PUBLIC SETTNGS!
WARNING: Assembly by adult.
AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte.
ADVERTENCIA: El ensamblaje lo debe hacer un adulto.
WARNING: ASSEMBLY BY ADULT.
WARNING: ASSEMBLY BY ADULT
Socket Wrench set /
Wrenches
Mallet
OR
KIT INCLUDES:
x2
1-1/4”
(3,2 cm)
Deck Screw
Tools Required:
Screw size should be a #8 thread size
minimum and coated for use
with treated wood.
Included In Kit
x22
x11
x11
Hex Bolt
x2
x4
1-1/2”
(3,8 cm)
1/4”
(6 mm)
1/2”
(12,7 mm)
#10 Truss Screw
Screw must be to sizes shown at a minimum.
Do not use a screw size shorter than 1-1/2”
(3,8 cm) long.
5
9
7
11
2
3
10
8
4
6
1

Summary

Assembly Steps

Backing Plates and Slide Assembly

Instructions for aligning and attaching slide sections with backing plates using bolts, washers, and lock-nuts.

Slide Placement and Securing

Use Zone and Stake Installation

Guidance on positioning the slide within the 'Use Zone' and securing it to a ground stake.

Attaching Slide to Unit

Instructions for connecting the slide to the playset deck, noting dimple placement and potential screw protrusion.

Safety Checklist for Play Sets and Accessories

Installation Safety

Checklist items for safe installation of play sets and accessories.

Operating Safety

Checklist items for safe operation and supervision of play sets.

Safety Maintenance

Preventive maintenance guidelines for play set safety and longevity.

Disposal Instructions

Guidelines for safely disassembling and disposing of play equipment.

Additional Safety Installation Instructions

Required safety instructions for anchoring and protective surfacing for play equipment.

Warranty Information

Manufacturers Limited Warranties

Details on lifetime, 5-year, and accessory warranties for play sets and components.

Warranty Exclusions

Conditions and actions that void the manufacturer's warranty.

Swing-N-Slide WS 5037 Specifications