Swing-N-Slide WS 8338

To Next Page

Speciﬁ cations subject to change without notice.

Manufactured for: Swing-N-Slide® • 1212 Barberry Drive • Janesville, Wisconsin 53545 • USA • 1-800-888-1232 • www.swing-n-slide.com

Made in USA • Printed in USA

ASSEMBLY STEPS

1. Cut lumber as indicated in Fig. 1. Assembly requires (2) 36” legs,

(2) 15” cross supports and (1) 17’’ stake. Angle the tops of the (2)

36” legs as indicated.

2. Assemble the slide support using (3) 2-1/2’’ Deck Screws at

each joint.

3. Assemble the slide halves with (1) bolt, (2) washers and (1) loc

nut

at each hole as indicated in Fig. 2.

LDR 02-21-2019 LA 9435

2" x 4" x 15"

12"

1-1/2"

2" x 4" x 15"

2" x 4" x 36"

Side Winder Slide Instructions

WS 8338, WS 8339,

NE 4678-1TB, NE 4678-1YB

x19

Fig. 1

Fig. 2

Not Included In Kit:

Fits 48” or 60” (121,9 cm or 152,4 cm) Deck Height

FOR PRIVATE USE ONLY

DO NOT USE IN PUBLIC SETTNGS!

x1 x1

Weight Limit: 250 lbs

For children 2-10 years of age

Stake

2” x 4” x 17” (5,1 x 10,2 x 43,1 cm)

Use Pressure-Treated Wood

1-3/4”

(4,4 cm)

17” (43,1 cm)

Cut

1-3/4” (4,4 cm)

Tape Measure

Hammer

1/8” & 1/4” Drill Bits

Phillips Bit

WARNING: Assembly by adult.

AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte.

ADVERTENCIA: El ensamblaje lo debe hacer un adulto.

WARNING: ASSEMBLY BY ADULT.

WARNING: ASSEMBLY BY ADULT

Circular Saw

Electric Drill

Socket Wrench set /

Wrenches

Cut

KIT INCLUDES:

Hex Bolt

x12

2-1/2”

(6,3 cm)

Deck Screw

1-1/4”

(3,2 cm)

1/4”

(6 mm)

1/2”

(12,7 mm)

Truss Screw

Tools Required:

Screw size should be a #8 thread size minimum

and coated for use with treated wood.

Screw must be to sizes shown at a

minimum. Do not use a screw size

shorter than 1-1/4” (3,2 cm) long.

Slide Support Lumber

2” x 4” x 12’ (5,1 x 10,2 x 366 cm)

Use Pressure-Treated Wood

144’ (366 cm)

Need help?

Do you have a question about the Swing-N-Slide WS 8338 and is the answer not in the manual?

Summary

Assembly Steps

Cut Lumber and Prepare Supports

Cut lumber as indicated and prepare slide support legs and cross supports.

Assemble Slide Support

Assemble the slide support using deck screws at each joint.

Assemble Slide Halves

Assemble the slide halves using bolts, washers, and lock nuts.

Attach Slide to Platform

Line up slide to platform and attach using truss head screws.

Attach Slide Support Brace

Attach slide support to the bottom half of the slide and secure brace.

Anchor Slide to Ground

Prepare ground, drive stake, and attach slide to stake using a screw.

Safety Checklist and Instructions

Installation Safety Checklist

Checklist for safe installation practices and warnings.

Operating Safety Checklist

Checklist for safe operation and child supervision.

Safety Maintenance Guidelines

Preventive maintenance instructions for safety and longevity.

Disposal Instructions

Guidelines for safely disassembling and disposing of equipment.

Additional Required Safety Installation

Crucial instructions for anchoring and protective surfacing.

Warranty and Registration Information

Manufacturers Limited Warranties

Details on lifetime, 5-year, and accessory warranties.

Warranty Exclusions and Limitations

Conditions under which the warranty is void or does not apply.