SystemAir K 160 XL User Manual

10 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

K/KV < 125W

Fans

Operating & Maintenance

202341 · A021

Table of Contents

Questions and Answers:

M
Matthew NelsonAug 6, 2025
What to do if SystemAir Fan air output is not sufficient?
- K
  Kenneth ThomasAug 6, 2025
  If the air output of your SystemAir Fan is not sufficient, consider these possible causes and solutions: * Ensure the fan impeller turns in the correct direction by verifying the electrical connection. * Check that the electrical connection matches the wiring diagrams. * Adjust the airflow shutters to ensure they are fully open. * Remove any blockage in the air inlet or duct system. * Confirm the product is suitable for the installation location. * For EC motors, check the ambient temperature and ensure sufficient space around the motor for cooling. If the air pressure is too low, make necessary changes to the duct system and installed components to increase it.
G
garrettbillyAug 10, 2025
Why SystemAir Fan motor does not rotate?
- S
  Stephanie SullivanAug 10, 2025
  If the motor of your SystemAir Fan does not rotate, it could be due to several reasons: * A component in the power supply might be defective; check the power supply, replace any defective components, and reconnect it. * The electrical connection may be incorrect; ensure it agrees with the wiring diagrams. * The motor protection might be released due to overheating; let the motor cool, reset the motor protection, and identify the cause of overheating. * A phase loss might have occurred; if it's a 3-phase motor, ensure no phase is missing.
B
bakerlaceyAug 14, 2025
How to fix unusual noise when SystemAir Fan starts or operates?
- M
  megan56Aug 14, 2025
  If there is unusual noise when your SystemAir Fan starts or operates, it might be due to strain in the duct system connections. To resolve this, loosen the connections, correctly align the parts of the duct system, and then tighten the connections.
C
Carly WoodsAug 19, 2025
What to do if SystemAir Fan does not operate smoothly?
- J
  Jeffrey AlvarezAug 19, 2025
  If your SystemAir Fan does not operate smoothly, consider the following: * Ensure the electrical connection is correct so that the fan impeller turns in the correct direction. * Clean the fan impeller carefully if there is dirt on it. * If the fan impeller has deformations because of too high temperatures: * Replace the fan impeller. * Make sure that the temperature of the transported air is not higher than the value on the name plate. * Ensure the product is correctly installed and check the duct system if there are unusually strong vibrations in the product or the duct system. * Increase or decrease the fan speed until the product operates smoothly if it is operated in a resonant frequency range.
R
reginahillAug 22, 2025
Why is SystemAir Fan electronic components or the motor overheated?
- M
  Mary JonesAug 23, 2025
  If the electronic components or the motor of your SystemAir Fan is overheated, it could be due to: * Motor overload or high ambient temperature. Let the motor cool, reset the motor protection, and find the cause of the overheating. * Insufficient cooling. Ensure adequate space around the motor for cooling. * The product is not applicable for the installation location.
B
Brittany BurgessAug 27, 2025
What to do if SystemAir Fan speed does not get the nominal value?
- R
  Robert CastroAug 27, 2025
  If the fan speed of your SystemAir Fan does not reach the nominal value, consider these possible causes: * Defective motor winding: If possible, measure the resistance to check the motor winding. * Incorrect speed control setting: Set the speed control correctly. * Mechanical blockage: Remove any blockage preventing the fan impeller from turning freely. * Phase loss: If it is a 3-phase motor, ensure that no phase is missing.
S
Scott BlakeAug 31, 2025
What causes SystemAir Fan thermal contacts, PTC or resistors to be released?
- S
  Stephanie ElliottAug 31, 2025
  If thermal contacts, PTC, or resistors are released in your SystemAir Fan, it could be due to several reasons: * Ensure the fan impeller turns in the correct direction by verifying the electrical connection. * If the motor is a 3-phase motor, make sure that no phase is missing. * The motor may be overheated. Check the motor cooling impeller, and if possible, measure the resistance to check the motor winding. * The capacitor may not be connected correctly. Connect the capacitor correctly, referring to the included motor wiring diagram. Note: This is not applicable for EC motors or 3–phase AC motors.

SystemAir K 160 XL Specifications

General

Brand	SystemAir
Model	K 160 XL
Category	Fan
Language	English

Related product manuals

SystemAir K 160 M

SystemAir K 160 EC

SystemAir K 160 XL sileo

Preview: SystemAir K 100 M

SystemAir K 100 M

SystemAir K 125 EC

SystemAir K 125 XL

Preview: SystemAir K 100 M sileo

SystemAir K 100 M sileo

SystemAir K 100 XL sileo

SystemAir K 125 XL sileo

Preview: SystemAir K Series

SystemAir K Series

Preview: SystemAir K-EF Series

SystemAir K-EF Series

SystemAir K 315 L sileo