RATED LIFTING CAPACITIES
ISO4305
-
12
-
SPEC. SHEET NO. GR-800E-2-00102/EX-04
ON OUTRIGGERS
A
B
C C C C C C C C C C
0˚ 12˚ 42˚ 0˚ 54˚ 43˚ 60˚ 53˚ 58˚ 63˚
ON OUTRIGGERS MIN EXTENDED 2.7m SPREAD
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MIN EXTENDED
360˚ ROTATION (Unit: ×1000kg)
12.0m 16.4m 20.8m 29.5m 38.3m 42.6m 47.0m
70
67
64
61
58
55
52
48
45
42
38
28
33.8
27.7
23.3
19.9
17.2
14.5
12.3
10.6
9.2
8.0
7.0
5.4
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
9.0
10.0
11.0
12.0
14.0
16.0
18.0
20.0
D
75
74
71
70
68
66
64
62
60
57
55
50
46
40
34
28.9
23.9
20.2
17.3
15.0
13.0
11.5
10.1
8.7
7.5
6.5
4.9
3.7
2.7
1.9
79
78
76
75
73
72
70
68
67
66
64
61
57
54
50
20.9
20.9
17.8
15.3
13.2
11.5
10.1
8.9
7.8
6.9
6.1
4.6
3.3
2.3
1.5
78
77
75
74
73
71
70
68
67
65
63
60
57
53
49
41
32
12
18.2
18.2
18.2
18.2
16.1
14.4
12.9
11.6
10.5
9.6
8.7
7.0
5.7
4.6
3.8
2.5
1.6
0.9
78
77
76
75
74
73
72
70
68
66
63
59
12.7
11.3
10.1
9.0
8.1
7.3
6.6
5.4
4.4
3.6
2.8
1.6
78
77
76
75
74
73
72
70
68
66
63
59
54
49
14.6
13.1
11.9
10.8
9.9
9.1
8.3
7.1
6.1
5.1
4.3
3.0
2.1
1.4
78
77
77
75
74
72
71
67
64
7.8
7.1
6.5
5.4
4.5
3.8
3.1
2.0
1.1
79
78
77
76
74
72
71
68
64
61
57
8.5
8.5
7.8
6.7
5.8
5.0
4.4
3.2
2.3
1.6
1.0
77
76
74
73
70
67
64
5.9
5.1
4.4
3.6
2.5
1.7
1.0
78
76
75
72
69
4.4
3.6
2.9
1.9
1.1
A
C
B B
2.7m SPREAD 360˚ ROTATION (Unit: ×1000kg)
12.0ｍ 20.8ｍ
9.8
4.0
0˚
18.3
0.8
100
100
100
100
0
0
0
0
50
0
0
0
100
0
0
0
0
33
33
33
100
33
33
33
0
66
66
66
100
66
66
66
0
100
100
100
50
100
100
100
Telescoping conditions(%)
,
Telescoping
Mode
Telescoping
Mode
2nd boom
3rd boom
4th boom
Top boom
,
,
A: Boom length (m)
B: Load radius (m)
C: Loaded boom angle ( ˚)
D: Minimum boom angle ( ˚) for indicated boom length (no load)
NOTES FOR “ON OUTRIGGERS” TABLE
a
a
a
a
Outriggers extended width 6.7m(middle) 5.5m(middle) 2.7m(minimum)
Angle a
˚
60 40 10
1. Rated lifting capacities shown in the table are based on condition that crane is set on firm level surface. Those above thick lines are
based on crane strength and those below, on its stability.
2. Rated lifting capacities based on crane stability are according to ISO4305.
3. Rated lifting capacities shown in the table are based on condition that crane is set on firm level surface. Those above thick lines are
based on crane strength and those below, on its stability.
4. The mass of the hook (800 kg for 90.7 t capacity, 540 kg for 60 t capacity, 450 kg for 35 t capacity, 165 kg for 6.6 t capacity), slings
and all similarly used load handling devices must be considered as part of the load and must be deducted from the lifting capacities.
5. For rated lifting capacity of single top, reduce the rated lifting capacities of relevant boom according to a weight reduction for
auxiliary load handling equipment. Capacities of single top shall not exceed 6,600 kg including main boom hook mass and the net
capacity must be so reduced.
6. Standard number of parts of line for each boom length is as shown below. Load per line should not surpass 64.7 kN {6,600 kgf} for
main winch and auxiliary winch.
The lifting capacity data stored in the Automatic Moment Limiter (AML) is based on the standard number of parts of line listed
in the chart.
Maximum lifting capacity is restricted by the number of parts of line of Automatic Moment Limiter (AML).
7. The lifting capacity for over-side area differs depending on the outrigger extension width. Work with the capacity corresponding to
the extension width. The lifting capacities for over-front and over-rear areas are for “outriggers fully extended”. However, the areas
(angle a) differ depending on the outrigger extension width.
Telescoping mode I, II I II I, II I, II
Number of parts of line 14 8 4 4 1
12.0m
12.0m to
20.8m
20.8m to
47.0m
Single top
Jib
Boom length
To Next Page
Loading...
