How to resolve Font Dnld Error on TallyGenicom 6300 Printer?
A 'Font Dnld Error' on your TallyGenicom printer indicates an error during a font download. To fix this, correct the data and retransmit it from the host.
What to do if TallyGenicom Printer shows Ribbon Fault?
If your TallyGenicom printer displays a Ribbon Fault, first, press the Clear key and attempt to print again. If the error persists, try turning the Ribbon Knob. If the knob is stuck, inspect the ribbon path for any obstructions, such as the hammer bank. If the Ribbon Knob remains immobile and the ribbon isn't caught, replace the ribbon cartridge with a new one.
Why does my TallyGenicom Printer show Data Overrun error?
A Data Overrun error on your TallyGenicom printer typically indicates an issue with the serial communication settings. This is most likely caused by an incorrectly configured serial baud rate, data bits, or parity. To resolve this, check the Serial Baud Rate, Data Bits, and Parity parameters through the printer control panel and adjust them as needed.
What to do if TallyGenicom Printer shows Buffer Overflow?
A Buffer Overflow error on your TallyGenicom printer typically occurs because the host isn't responding to a busy signal. To fix this, ensure the correct protocol is selected. Also, check the wiring of the I/O cable between the host and the printer to make sure it is properly connected.
How to fix a Bad Packet error on my TallyGenicom Printer?
A 'Bad Packet' error on your TallyGenicom printer indicates a communication fault between the I/O processor and the main processor. To resolve this, cycle the power and try again. If the problem returns, remove and replace the Engine Controller Board. If the problem persists, download new printer firmware.
What does Graphic Check mean on my TallyGenicom 6300 Printer?
The 'Graphic Check' message on your TallyGenicom printer means it has received an unprintable graphic. This message appears only if the Set Graphic Error Action Command is properly configured. Clear the message using the Clear key, then put the printer back online. Confirm with the host why the Graphic check message was sent.
What causes Bad TWICO Int. error on TallyGenicom 6300 Printer?
A 'Bad TWICO Int.' error indicates that the Twinax PSIO is damaged or corrupted. To resolve this, cycle the power and try again. If the problem persists, remove and replace the Twinax PSIO Assembly.
What does Chnl Not Found mean on my TallyGenicom Printer?
The 'Chnl Not Found' error on your TallyGenicom printer means that the VFU Channel requested by the host computer cannot be found. To fix this, correct the data from the host, then retransmit it to the printer.
What to do if TallyGenicom Printer shows Hammer Voltage error?
The 'Hammer Voltage' error on your TallyGenicom printer indicates an internal inconsistency detected by the software controlling the print hammer timing. Press the Clear key. If the error occurs repeatedly, skip to the next print job.
Overview of the 6300 Series printers and their capabilities.
Explains the conventions used throughout the manual for clarity.
Guidance on choosing an appropriate location for the printer.
Instructions for unpacking and removing securing hardware before operating the printer.
Guidance on installing the rear guide assembly and connecting I/O cables.
Steps for powering on the printer after initial setup.
Identifies key parts of the printer's paper handling system.
Step-by-step instructions for installing a new ribbon cartridge.
Overview of the printer's control panel, including indicators and display.
Detailed steps for loading paper into the printer.
Explains automatic, manual, and fine-tuning print gap settings.
Steps to create and save custom print gap profiles for specific forms.
How to save and manage printer configurations for different forms.
Overview of the control panel display and functionality of each key.
Guide on navigating the printer's menu system.
Detailed explanation of configuration options accessible via the control panel.
Accessing diagnostic tests and calibration routines through the control panel.
Explains messages indicating printer faults and errors.
Steps to follow for correcting detected printer faults.
Common paper handling and print quality issues and their solutions.
Guidance on connecting interface cables and powering up the printer.
Instructions for installing and connecting Twinax and Coax interfaces.
Overview of industry and agency standards the printer meets.
Details on printer dimensions, weight, and operating environment.
Information on the printer's power supply and heat output.
List of supported emulations, fonts, and character sets.
General| Brand | TallyGenicom |
|---|---|
| Model | 6300 Series |
| Category | Printer |
| Language | English |
To Next Page
