TallyGenicom 2365 User Manual

TallyGenicom 2365

186 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

User guide Matrix printer

2365

2380

Table of Contents

Default Chapter3
- Table of Contents3
Introduction11
- Printer Features11
- Symbols Used11
- About this Manual12
Printer at a Glance13
- Printer in Tractor Mode14
- Paperway15
Installation17
- Unpacking the Printer17
- Placing Your Printer18
- Checking the Printer Voltage19
- Connecting the Printer19
- Switching on the Printer20
Inserting the Ribbon Cassette21
- Installing the Ribbon Cassette the First Time21
- Changing the Ribbon Cassette27
Printer Drivers33
- Installing a Printer Driver in Windows 95/98/ME33
- Installing a Printer Driver in Windows 2000/2003/XP34
- Other Operating Systems35
- Changing Printer Settings36
  - Form Settings (Windows 2000/2003/XP)36
- Loading Optional Firmware37
  - Troubleshooting37
The Control Panel39
- The LC Display40
- Online Mode41
- Offline Mode41
- Setup Mode42
- Messages in the LC Display43
- Key Functions When Turning on the Printer45
Paper Handling47
- Loading Paper47
- Paper Transport50
- Moving the Paper to the Tear Position51
- Removing Paper52
Settings53
- Setting the Print Head Gap53
- Setting the Tear Position54
- Setting the First Printing Line (TOF)55
- Selecting Character Density and Font56
Model57
- Introduction57
  - Rear Tractor Paper Path57
- Loading Paper into the Rear Tractor58
- Paper Guiding Bracket60
- Selecting the Rear Tractor60
The Menu63
- Programming Via the Control Panel63
- Enabling Access to Menu Mode63
- Calling up the Menu63
- Menu Configurations64
- Menu Handling65
  - Save Settings65
  - Selecting the LC Display Language66
  - Terminating Setup Mode67
- Menu Structure68
- Menu Parameters69
  - Printing out Menu Configurations (Print)69
  - Loading Menu Configurations (Menu)69
  - Reset to Default Values (Reset)70
  - Quietmode (Quietm.)70
  - Selecting Font (Font)71
  - Setting Character Density (CPI)72
  - Setting Line Spacing (LPI)72
  - Skiping Perforation (Skip)73
- Selecting Start Signal for Escape Sequence (Escchar)73
- Selecting Emulation (Emulate)74
- Bidirectional Printing (Bidir)74
- Settings for Interfaces (I/O)75
- Serial Interface (Serial)75
  - Data Transmssion Rate (Baud)75
  - Data Format (Format)76
  - Further Settings (Special)77
  - Error Handling (Errmode)77
  - Block End Character (Blockend)77
  - Signal Feedback (Remote)78
  - Transparence (Handthr)78
  - Protocol (Protocol)79
  - Signal Processing (DTR)79
- Selecting Interface (Interf.)80
- Interface Buffer (Buffer)80
- Ethernet Interface (ETH-INT)81
  - Setting IP Address (IP Addr)81
  - Setting Gateway Address (Gateway)81
  - Setting Subnet Mask (Subnet)82
  - IP Address Administration (IP Get M)83
  - Banner Page (Banner)83
  - Ethernet Speed (Ethspeed)84
- Selecting Character Set (CG-Tab)85
- IBM Character Set (Charset)85
- National Character Set (Country)86
- Slashed Zero (Sl.zero)86
- Automatic Carriage Return (Auto-CR)87
- Automatic Line Feed (Auto-LF)87
- Menu Lock (Menlock)88
- Language (Language)88
- Paper Parameters (Paper)89
  - Form Length (Forml)89
  - First Printing Position (Formadj)91
  - Printhead Gap Manually (Head)92
- View and Tear Position (Autotear)93
  - Line Length (Width)94
  - Barcode (Barcode)94
  - Normal Characters and Barcode (Barmode)95
  - Vertical Position after Oversized Barcode (Bartop)95
  - Vertical Position after Oversized Character (Lcptop)96
  - Form Feed Mode (Ffmode)97
  - Setting and Activating Options (Papopt)98
    - Activation of Tractors (Autotra)98
    - Activation of Automatic Sheet Feeder (Autoasf)99
  - Menu Settings (Example)100
Advanced Menu101
- Test Functions101
  - Printer Self-Test (Rolling ASCII)102
    - Exiting Rolling ASCII Test Mode103
  - Interface Test (Hex-Dump)104
    - Printout in Hex-Dump104
    - Terminating Hex-Dump105
- Advanced Settings106
Troubleshooting119
- General Print Problems120
- Problems with the Print Quality123
- Error Messages Via the Display124
- Additional Display Messages128
Care and Maintenance129
- Replacing the Fuse129
- Cleaning the Housing130
- Cleaning the Interior130
- Cleaning the Platen131
- Ribbon131
- Cleaning the Upper Friction132
- Carriage Shafts132
Specifications133
- Printer Specifications133
- Interface Specifications137
- Paper Specifications138
Character Sets139
- MTPL Standard Character Set140
- MTPL, International Substitution Characters141
- OCR-A Character Set142
- OCR-B Character Set143
- Available Character Sets and Fonts144
Emulations147
- General147
- Escape Sequences147
- What Are Escape Sequences148
- How Are Escape Sequences Used149
  - Mtpl149
- List of Available Control Codes150
  - Genicom ANSI Emulation160
- Barcode162
Interfaces167
- Parallel Interface168
  - Connector Assignment168
- Ethernet Interface169
- Optional Serial Interface V.24/RS232C171
Options and Accessories175
- Options175
- Accessories177
  - Ribbon Cassettes177
  - Programming Manuals177
Index179

Other manuals for TallyGenicom 2365

Maintenance Manual184 pages

Questions and Answers:

Need help?

Do you have a question about the TallyGenicom 2365 and is the answer not in the manual?

TallyGenicom 2365 Specifications

General

Brand	TallyGenicom
Model	2365
Category	Printer
Language	English

Related product manuals

TallyGenicom 2380

Preview: TallyGenicom 2248

TallyGenicom 2248

Preview: TallyGenicom MATRIX PRINTER 2150

TallyGenicom MATRIX PRINTER 2150

Preview: TallyGenicom 6800 Series

TallyGenicom 6800 Series

Preview: TallyGenicom 5040

TallyGenicom 5040

Preview: TallyGenicom Matrix Printer

TallyGenicom Matrix Printer

Preview: TallyGenicom 6600 Series

TallyGenicom 6600 Series

Preview: TallyGenicom 6300 Series

TallyGenicom 6300 Series

Preview: TallyGenicom LMPPLS

TallyGenicom LMPPLS