TallyGenicom 2365 - About this manual

TallyGenicom 2365

186 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Default Chapter3
- Table of Contents3
Introduction11
- Printer Features11
- Symbols Used11
- About this Manual12
Printer at a Glance13
- Printer in Tractor Mode14
- Paperway15
Installation17
- Unpacking the Printer17
- Placing Your Printer18
- Checking the Printer Voltage19
- Connecting the Printer19
- Switching on the Printer20
Inserting the Ribbon Cassette21
- Installing the Ribbon Cassette the First Time21
- Changing the Ribbon Cassette27
Printer Drivers33
- Installing a Printer Driver in Windows 95/98/ME33
- Installing a Printer Driver in Windows 2000/2003/XP34
- Other Operating Systems35
- Changing Printer Settings36
  - Form Settings (Windows 2000/2003/XP)36
- Loading Optional Firmware37
  - Troubleshooting37
The Control Panel39
- The LC Display40
- Online Mode41
- Offline Mode41
- Setup Mode42
- Messages in the LC Display43
- Key Functions When Turning on the Printer45
Paper Handling47
- Loading Paper47
- Paper Transport50
- Moving the Paper to the Tear Position51
- Removing Paper52
Settings53
- Setting the Print Head Gap53
- Setting the Tear Position54
- Setting the First Printing Line (TOF)55
- Selecting Character Density and Font56
Model57
- Introduction57
  - Rear Tractor Paper Path57
- Loading Paper into the Rear Tractor58
- Paper Guiding Bracket60
- Selecting the Rear Tractor60
The Menu63
- Programming Via the Control Panel63
- Enabling Access to Menu Mode63
- Calling up the Menu63
- Menu Configurations64
- Menu Handling65
  - Save Settings65
  - Selecting the LC Display Language66
  - Terminating Setup Mode67
- Menu Structure68
- Menu Parameters69
  - Printing out Menu Configurations (Print)69
  - Loading Menu Configurations (Menu)69
  - Reset to Default Values (Reset)70
  - Quietmode (Quietm.)70
  - Selecting Font (Font)71
  - Setting Character Density (CPI)72
  - Setting Line Spacing (LPI)72
  - Skiping Perforation (Skip)73
- Selecting Start Signal for Escape Sequence (Escchar)73
- Selecting Emulation (Emulate)74
- Bidirectional Printing (Bidir)74
- Settings for Interfaces (I/O)75
- Serial Interface (Serial)75
  - Data Transmssion Rate (Baud)75
  - Data Format (Format)76
  - Further Settings (Special)77
  - Error Handling (Errmode)77
  - Block End Character (Blockend)77
  - Signal Feedback (Remote)78
  - Transparence (Handthr)78
  - Protocol (Protocol)79
  - Signal Processing (DTR)79
- Selecting Interface (Interf.)80
- Interface Buffer (Buffer)80
- Ethernet Interface (ETH-INT)81
  - Setting IP Address (IP Addr)81
  - Setting Gateway Address (Gateway)81
  - Setting Subnet Mask (Subnet)82
  - IP Address Administration (IP Get M)83
  - Banner Page (Banner)83
  - Ethernet Speed (Ethspeed)84
- Selecting Character Set (CG-Tab)85
- IBM Character Set (Charset)85
- National Character Set (Country)86
- Slashed Zero (Sl.zero)86
- Automatic Carriage Return (Auto-CR)87
- Automatic Line Feed (Auto-LF)87
- Menu Lock (Menlock)88
- Language (Language)88
- Paper Parameters (Paper)89
  - Form Length (Forml)89
  - First Printing Position (Formadj)91
  - Printhead Gap Manually (Head)92
- View and Tear Position (Autotear)93
  - Line Length (Width)94
  - Barcode (Barcode)94
  - Normal Characters and Barcode (Barmode)95
  - Vertical Position after Oversized Barcode (Bartop)95
  - Vertical Position after Oversized Character (Lcptop)96
  - Form Feed Mode (Ffmode)97
  - Setting and Activating Options (Papopt)98
    - Activation of Tractors (Autotra)98
    - Activation of Automatic Sheet Feeder (Autoasf)99
  - Menu Settings (Example)100
Advanced Menu101
- Test Functions101
  - Printer Self-Test (Rolling ASCII)102
    - Exiting Rolling ASCII Test Mode103
  - Interface Test (Hex-Dump)104
    - Printout in Hex-Dump104
    - Terminating Hex-Dump105
- Advanced Settings106
Troubleshooting119
- General Print Problems120
- Problems with the Print Quality123
- Error Messages Via the Display124
- Additional Display Messages128
Care and Maintenance129
- Replacing the Fuse129
- Cleaning the Housing130
- Cleaning the Interior130
- Cleaning the Platen131
- Ribbon131
- Cleaning the Upper Friction132
- Carriage Shafts132
Specifications133
- Printer Specifications133
- Interface Specifications137
- Paper Specifications138
Character Sets139
- MTPL Standard Character Set140
- MTPL, International Substitution Characters141
- OCR-A Character Set142
- OCR-B Character Set143
- Available Character Sets and Fonts144
Emulations147
- General147
- Escape Sequences147
- What Are Escape Sequences148
- How Are Escape Sequences Used149
  - Mtpl149
- List of Available Control Codes150
  - Genicom ANSI Emulation160
- Barcode162
Interfaces167
- Parallel Interface168
  - Connector Assignment168
- Ethernet Interface169
- Optional Serial Interface V.24/RS232C171
Options and Accessories175
- Options175
- Accessories177
  - Ribbon Cassettes177
  - Programming Manuals177
Index179

Other manuals for TallyGenicom 2365

Maintenance Manual184 pages

Related product manuals

TallyGenicom 2380

Preview: TallyGenicom 2248

TallyGenicom 2248

Preview: TallyGenicom 2150

TallyGenicom 2150

Preview: TallyGenicom 2265+

TallyGenicom 2265+

Preview: TallyGenicom MATRIX PRINTER 2150

TallyGenicom MATRIX PRINTER 2150

Preview: TallyGenicom 6800 Series

TallyGenicom 6800 Series

Preview: TallyGenicom 5040

TallyGenicom 5040

Preview: TallyGenicom Matrix Printer

TallyGenicom Matrix Printer

Preview: TallyGenicom 6600 Series

TallyGenicom 6600 Series

Preview: TallyGenicom 6300 Series

TallyGenicom 6300 Series

Preview: TallyGenicom 6605

TallyGenicom 6605

TallyGenicom 6615Q