Tascam DA-30 - Page 13

2-3-7.
Disassembly
of
the
cassette
holder
unit
(Fig.
2-16)
Fig. 2-16
Holder cassette
23 20s
feos ee ee hed
AtybhsANIF-+ 2=ybhORM
(2-16)
Drive gear
Timing gear
Holder block
1.
Removal
of
the
holder
cassette
j
{.
Remove
two
screws
@)
shown
in
Fig.
2-16,
then
remove
the
tray.
1,
HOLDER
CASSETTE
OMAL
I.
Rl2-16DAV@LZALAL, FET EMAT.
If,
Remove
washers
©
and
©
shown
in
Fig.
2-16,
OD.
SM2-16974%+-@,
OAL,
DRIVE
GEAR,
TIM!
then
remove
the
drive
gear
and
timing
gear.
111.
Remove
the
holder
cassette
shown
in
Fig.
2-16
NG
GEAR
IMAG.
by
sliding
it
forward.
.
:
e
WM.
BY2-16DHOLDER
CASSETTE
SAI
AS
4
KAUTHR
Note
1:
Handle
the
holder
cassette
with
care
so
:
that
it
is
not
damaged,
dented,
etc.
AT.
:
i
li
ull
wise
Note:
pha
enctaagat
See
i
ees
721.
HOLDER
CASSETTE
(2%.
JTBE
tee
ICRU
(direction
A
in
Fig.
2-17),
then
reinstall
webterace.
the
timing
gear
with
the
front
of
the
;
holder
cassette
positioned
in
accordance
7E
2.
HOLDER
CASSETTE
MASiASHFIS,
HOLDER
BLES
ANE
la
aa
=
OAM
ONS”:
SERIAL
CBl2-17
AZ).
HOLDER
CASSE
FTE
WE
R-17
OTH
(1.
9T0.
dom)
CSU
ALKES
T
TIMING
GEARTMAAGC
EC.
‘1.9
mm
+0.4
Holder
block
Fig. 2-17
Removal of the holder block
1. Remove three screws @ shown in Fig. 2-16,
then remove the rack gear.
Il. Remove three screws © shown in Fig. 2-16,
then remove three tray bushings. .
ill. Remove the holder block shown in Fig. 2-16.
Removal of the slider ~
{. Remove two springs shown in Fig. 2-16
I. Remove two screws © shown in Fig. 2-16, then
remove the slider cover.
Ill. Remove six screws © shown in Fig. 2-16, then
remove two front spacers. ,
IV. Remove the slider shown in Fig, 2-16.
Note: Handle the slider with care so that it is
not damaged, dented, etc.
2. HOLDER BLKD ERY L
I.
Qh.
.
Ble-16D
ex
VQOSAKEAL,
RACK
GEAR
ZRAF.
B2-16D%
YOBAEAL,
TRAY
BUSHINGS
HERA
tv.
Gl2-16DHOLDER BLKE RAY.
3. SLIDERORAL
I.
Bl2-16D AF VY AF LZRKENT.
I.
B2-1sDR
YOD2AKEAL,
SLIDER
COVEREMAT.
Bl2-16DAYO@EARENL,
FRONT
SPACER
2%
BX
Tt.
Rl2-16DSLIDERE MAT.
SLIDERIZ
HH,
ITH
BETIS
ORC
MIRO
CERT
S
cé.
13