6-156-15TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
g y yg y y
maintenance personnel.maintenance personnel.
55. . - - TThhiis s iiccoon n wwiilll l cchhaanngge e ffrroom m wwhhiitte e tto o rreedd
when the engine oil pressure has fallen belowwhen the engine oil pressure has fallen below
10 psi (.7 bar) at 750 rpm or less than 40 psi10 psi (.7 bar) at 750 rpm or less than 40 psi
(2.8 bar) at (2.8 bar) at 1,600 rpm. 1,600 rpm. If this If this icon changes icon changes toto
red, stop the engine immediately and notifyred, stop the engine immediately and notify
maintenance personnel.maintenance personnel.
6. 6. - T- Thhiis is iccoon wn wiilll cl chhaanngge fe frroom wm whhiitte te to ro reedd
when the battery voltage is less than 9 VDC orwhen the battery voltage is less than 9 VDC or
greater than 15 greater than 15 VDC. VDC. This icon This icon will be wwill be whitehite
when the battery voltage is greater than 9when the battery voltage is greater than 9
VDC or less VDC or less than 15 VDC. than 15 VDC. If this icon If this icon changeschanges
to red, stop the engine immediately and notifyto red, stop the engine immediately and notify
maintenance personnel.maintenance personnel.
7. 7. - T- Thihis is icocon fn flalasshehes ws whehen tn the he seseat at bebelt lt isis
unfastened.unfastened.
8. 8. - T- Thhiis is iccoon in illlluummiinnaattees ws whehen tn thhe pe paarrkkiinngg
brake is applied.brake is applied.
9. 9. - T- Thhiis is iccon on ffllaasshhees ws whheen a n a lloow hw hyyddrraauulliicc
pressure problem (below 1,500 psipressure problem (below 1,500 psi/ 104 bar)/ 104 bar)
exists in the service brake apply circuit.exists in the service brake apply circuit.
1010. . - - ThThis is icicon on flflasashehes fs for or 30 30 sesecocondnds s bebefoforere
the engine ECM shuts down the truck due tothe engine ECM shuts down the truck due to
high transmission temperature.high transmission temperature.
12.12. F1 - Depress this F1 - Depress this button to view tbutton to view the Diagnos-he Diagnos-
tics Select screen.tics Select screen.
13.13. F2 - Depress F2 - Depress this button to this button to view Activeview Active
Warnings.Warnings.
14.14. F3 - Depress F3 - Depress this button tthis button to manually enable oro manually enable or
disable the forward alarm while the forwarddisable the forward alarm while the forward
alarm is in the Operator Controlled Manualalarm is in the Operator Controlled Manual
mode of operation [refer to themode of operation [refer to the ForwardForward
Alarm SystemAlarm Systemin the Operator’s Guidein the Operator’s Guide
(OG160) for detailed information].(OG160) for detailed information].
15.15. F4 - F4 - Reserved for Reserved for optional functions.optional functions.
16.16. UP and DOWN UP and DOWN - Depress eit- Depress either button toher button to
make adjustments or scroll through menus.make adjustments or scroll through menus.
NOTE:NOTE: Adjustments Adjustments should only should only be made be made byby
Maintenance Personnel!!Maintenance Personnel!!
17.17. OK - Depress OK - Depress this button this button to select a to select a high-high-
lighted item.lighted item.
18.18. Back - Depress Back - Depress this button to this button to back up throughback up through
the display screens.the display screens.
19.19. Measure / Adjust Measure / Adjust Groups - Depress Groups - Depress this buttonthis button
to select measure groups, adjust groups, infor-to select measure groups, adjust groups, infor-
mation screen or status page.mation screen or status page.
NOTE:NOTE: Adjustment groups Adjustment groups will be will be Pin CodePin Code
protected.protected. NOTE:NOTE: Adjustments Adjustments should should onlyonly
be made by Maintenance Personnel!!be made by Maintenance Personnel!!
To Next Page
Loading...
