TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
9C-109C-10
APC User Interface On TICS Transmission Information APC User Interface On TICS Transmission Information ScreenScreen
Display modeDisplay mode CommentComment
GPOSGPOS Reflects the actually engaged transmission direction and range.Reflects the actually engaged transmission direction and range.
VSPDVSPD Shows vehicle sShows vehicle speed in kmpeed in km/h or /h or MPH MPH (parameter (parameter setting). setting). Speeds areSpeeds are
shown with a 0.1 km/h or 0.1 shown with a 0.1 km/h or 0.1 MPH resolution.MPH resolution.
DISTDIST Shows the travelled distance in kShows the travelled distance in km or Miles (parameter m or Miles (parameter setting). setting). Distance isDistance is
shown with a shown with a 0.1 km or 0.1 km or 0.1 Mile resolution. 0.1 Mile resolution. By pressing the By pressing the “S” button (“S” button (F4)F4)
during 3 seconds, the distance trip counter is reset during 3 seconds, the distance trip counter is reset to 0.to 0.
OPEROPER Shows the total operatShows the total operating time of the vehing time of the vehicle (engine running). icle (engine running). Operating timeOperating time
is shown with a 1 hour resolution and has a range of 0 to 49,999 houris shown with a 1 hour resolution and has a range of 0 to 49,999 hours. s. TheThe
number digits show the hours, the number of dots in between show number digits show the hours, the number of dots in between show thethe
number of times 10,000 hours needs to be added to the number shown:number of times 10,000 hours needs to be added to the number shown:
1 1 2 2 3 3 4 4 = = 1234 1234 hourshours
1 2.3.4. = 31234 hours1 2.3.4. = 31234 hours
CPOSCPOS Reflects the current shift lever direction and position.Reflects the current shift lever direction and position.
ESPDESPD Shows measured engine speed (RPM)Shows measured engine speed (RPM)
TSPDTSPD Shows measured turbine speed (RPM)Shows measured turbine speed (RPM)
OSPDOSPD Shows measured output speed (RPM)Shows measured output speed (RPM)
SRATSRAT Reflects the current speed ratio (calculated as TSReflects the current speed ratio (calculated as TSPD/ESPD [turbine speed /PD/ESPD [turbine speed /
engine speed]) and is an important factor in automatic shifting.engine speed]) and is an important factor in automatic shifting.
TQ ITQ I Measured turbine torque at transmission input side (Nm)Measured turbine torque at transmission input side (Nm)
TTMPTTMP Shows transmission temperature inShows transmission temperature in °°CC
CTMPCTMP Shows cooler input temperature inShows cooler input temperature in °°CC
ERRERR The error displayThe error display. . By pressing the “S” button (F4) you can scroll through theBy pressing the “S” button (F4) you can scroll through the
errors codes. errors codes. If an error code is If an error code is blinking, this indicates that the blinking, this indicates that the error waserror was
active in the past, but not active anymore.active in the past, but not active anymore.
When the controller detects an error, tWhen the controller detects an error, the ’E’ led blinks slowly to he ’E’ led blinks slowly to indicate this. indicate this. YYou can always select theou can always select the
error display mode (ERR) to view the nature of error display mode (ERR) to view the nature of the problem. the problem. An overview of the error codes is included inAn overview of the error codes is included in
the back of this section (refer tothe back of this section (refer to APC Error Codes and DescriptionsAPC Error Codes and Descriptions).).
Operating ModesOperating Modes
Normal DrivingNormal Driving
For detailed description see functional description.For detailed description see functional description.
To Next Page
Loading...
