TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
9C-209C-20
0000..5522 SS TThheerre e iis s a a pprroobblleemm
related to the systemrelated to the system
RAM.RAM.
Controller reverts toController reverts to
a ”shut down” modea ”shut down” mode
and will force neutraland will force neutral
0.0.
Stop machine &Stop machine &
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Hardware relatedHardware related
fault – related to infault – related to in
the system RAM.the system RAM.
Contact Spicer Off–Contact Spicer Off–
Highway and informHighway and inform
the fault code andthe fault code and
the time that is wasthe time that is was
active.active.
0000..5533 SS TThheerre e iis s a a pprroobblleemm
related to the Flashrelated to the Flash
program memory.program memory.
Controller reverts toController reverts to
a ”shut down” modea ”shut down” mode
and will force neutraland will force neutral
0.0.
Stop machine &Stop machine &
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Hardware relatedHardware related
fault – related to infault – related to in
the flash programthe flash program
memory.memory.
Contact Spicer Off–Contact Spicer Off–
Highway and informHighway and inform
the fault code andthe fault code and
the time that is wasthe time that is was
active.active.
3300..0044 SS PPoowweer r ssuupppplly y oouut t oof f
range range –> –> belowbelow
minimum.minimum.
Controller will saveController will save
all logged informa-all logged informa-
tion to flash, will pow-tion to flash, will pow-
erdown, and force allerdown, and force all
outputs off.outputs off.
Stop machine &Stop machine &
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Power supply to thePower supply to the
controller too low:controller too low:
APC 12V supply APC 12V supply ver-ver-
sion: < 9 Vsion: < 9 V
APC 24V supply APC 24V supply ver-ver-
sion: < 16V.sion: < 16V.
Check power supplyCheck power supply
cables to the control-cables to the control-
ler. Check alternator,ler. Check alternator,
check the connec-check the connec-
tion cables betweention cables between
the battery and thethe battery and the
alternator, check thealternator, check the
battery.battery.
3300..0055 AA PPoowweer r ssuupppplly y oouut t oof f
range –> aboverange –> above
maximum.maximum.
The controller willThe controller will
have reduced pro-have reduced pro-
portional controlportional control
accuracy due toaccuracy due to
reduced PWM dutyreduced PWM duty
cycle.cycle.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Power supply to thePower supply to the
controller too high:controller too high:
APC 12V supply APC 12V supply ver-ver-
sion: > 18 Vsion: > 18 V
APC 24V supply APC 24V supply ver-ver-
sion: > 32 V.sion: > 32 V.
Check power Check power supplysupply,,
check if a jump startcheck if a jump start
setup is still con-setup is still con-
nected.nected.
3311..0000 AA VVoollttaagge e ssuupppplly y ffoorr
the sensors : Vsensethe sensors : Vsense
(8V) is out of range(8V) is out of range
–> below min–> below minimum.imum.
The controller willThe controller will
have reduced sensorhave reduced sensor
signals.signals.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Voltage supply forVoltage supply for
the sensors : Vsensethe sensors : Vsense
(8V) is below 7,2 V.(8V) is below 7,2 V.
Check power Check power supplysupply..
Check the controller.Check the controller.
3311..0011 AA VVoollttaagge e ssuupppplly y ffoorr
the sensors : Vsensethe sensors : Vsense
(8V) is out of range(8V) is out of range
–> above maximum.–> above maximum.
The controller willThe controller will
have reduced sensorhave reduced sensor
signals.signals.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Voltage supply forVoltage supply for
the sensors : Vsensethe sensors : Vsense
(8V) is above 8,8 V.(8V) is above 8,8 V.
Check power Check power supplysupply..
Check the controller.Check the controller.
4400..0066 AA IInnvvaalliid d sshhiifft t lleevveerr
direction detected.direction detected.
The controller willThe controller will
force neutral.force neutral.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The controllerThe controller
receives from thereceives from the
shift lever a requestshift lever a request
to engage forwardto engage forward
and reverse at theand reverse at the
same time.same time.
Check the wiringCheck the wiring
between the control-between the control-
ler and the shift leverler and the shift lever
concerning the for-concerning the for-
ward and the reverseward and the reverse
signal.signal.
FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
4400..0088 BB SSeeaat t oorriieennttaattiioon n iinnppuutt
was changed whilewas changed while
the parking brakethe parking brake
was not active, or/was not active, or/
and the shift leverand the shift lever
was not in neutral,was not in neutral,
or/and the machineor/and the machine
was not at was not at standstill.standstill.
The controller willThe controller will
force neutral.force neutral.
Stop the vehicle, putStop the vehicle, put
the shift lever in neu-the shift lever in neu-
tral and put the park-tral and put the park-
ing brake on until theing brake on until the
fault disappears.fault disappears.
Seat orientation inputSeat orientation input
was changed whilewas changed while
the parking brakethe parking brake
was not active, or/was not active, or/
and the shift leverand the shift lever
was not in neutral,was not in neutral,
or/and the machineor/and the machine
was not at was not at standstill.standstill.
Check the seat ori-Check the seat ori-
entation switch orentation switch or
train the driver totrain the driver to
change the seat ori-change the seat ori-
entation according toentation according to
the correct proce-the correct proce-
dure.dure.
4411..0066 AA IInnvvaalliid d sshhiifft t lleevveerr
position detected.position detected.
The controller will notThe controller will not
allow range shifting,allow range shifting,
however driving ishowever driving is
still possible.still possible.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The controllerThe controller
receives from thereceives from the
shift lever anshift lever an
unknown range shiftunknown range shift
patternpattern
Check the wiringCheck the wiring
between the control-between the control-
ler and the shift leverler and the shift lever
concerning the rangeconcerning the range
signalssignals
To Next Page
Loading...
