9C-219C-21TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
pattern.pattern. signals.signals.
4422..0044 SS//AA TThhe e aaccttuuaal l ttrraannssmmiiss--
sion ratio is too low.sion ratio is too low.
Controller will flagController will flag
the fault – this fault isthe fault – this fault is
indicating that one orindicating that one or
more clutches aremore clutches are
slipping.slipping.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The transmissionThe transmission
ratio measured byratio measured by
the controller is morethe controller is more
than 5% below thethan 5% below the
value of what isvalue of what is
should be.should be.
Check the transmis-Check the transmis-
sion, in order tosion, in order to
understand if andunderstand if and
which clutch is slip-which clutch is slip-
ping. ping. Check Check thethe
transmission ratiotransmission ratio
settings of the con-settings of the con-
troller.troller.
4422..0055 SS//AA TThhe e aaccttuuaal l ttrraannssmmiiss--
sion ratio is too high.sion ratio is too high.
Controller will flagController will flag
the fault – this fault isthe fault – this fault is
indicating that one orindicating that one or
more clutches aremore clutches are
slipping.slipping.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The transmissionThe transmission
ratio measured byratio measured by
the controller is morethe controller is more
than 5% above thethan 5% above the
value of what isvalue of what is
should be.should be.
Check the transmis-Check the transmis-
sion, in order tosion, in order to
understand if andunderstand if and
which clutch is slip-which clutch is slip-
ping. ping. Check Check thethe
transmission ratiotransmission ratio
settings of the con-settings of the con-
troller.troller.
4433..0033 AA TThhe e ttrraannssmmiissssiioonn
converter out tem-converter out tem-
perature sensor isperature sensor is
out of range.out of range.
Controller will flagController will flag
the fault.the fault.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The converter outThe converter out
temperature sensortemperature sensor
is not connected oris not connected or
shorted.shorted.
Check the wiringCheck the wiring
between the control-between the control-
ler and the converterler and the converter
out temperature sen-out temperature sen-
sor. sor. Check the Check the con-con-
verter out tempera-verter out tempera-
ture sensor.ture sensor.
4433..0077 AA TThhe e ttrraannssmmiissssiioonn
converter out tem-converter out tem-
perature sensor >perature sensor >
100100C.C.
Controller will flagController will flag
the fault – in order tothe fault – in order to
indicate indicate the dthe driver ofriver of
the warning level.the warning level.
Take notice of theTake notice of the
fault, and try to bringfault, and try to bring
the converter tem-the converter tem-
perature to a lowerperature to a lower
level.level.
The controller mea-The controller mea-
sured a convertersured a converter
out temperatureout temperature
between 100between 100C andC and
the allowed limit.the allowed limit.
Check the converterCheck the converter
out temperature andout temperature and
the converter outthe converter out
temperature sensor.temperature sensor.
4433..0088 AA TThhe e ttrraannssmmiissssiioonn
converter converter out out tem-tem-
perature sensor >perature sensor >
125125
C.C.
The controller is pro-The controller is pro-
tecting the transmis-tecting the transmis-
sion and does notsion and does not
allow that the con-allow that the con-
verter out tempera-verter out tempera-
ture exceeds its limit.ture exceeds its limit.
The controller willThe controller will
force the transmis-force the transmis-
sion to neutral, and ifsion to neutral, and if
engine is controlled,engine is controlled,
the engine will bethe engine will be
limited 50 % of itslimited 50 % of its
maximum speed.maximum speed.
Stop machine, selectStop machine, select
neutral and apply fullneutral and apply full
throttle (limited to 50throttle (limited to 50
%) in order to cool%) in order to cool
the transmission oilthe transmission oil
below 100below 100
C (untilC (until
the fault 43.03 isthe fault 43.03 is
gone). Once the con-gone). Once the con-
verter out tempera-verter out tempera-
ture is below 100ture is below 100C,C,
continue driving thecontinue driving the
machine.machine.
The controller mea-The controller mea-
sured a convertersured a converter
out temperatureout temperature
above the allowedabove the allowed
limit.limit.
Check the converterCheck the converter
out temperature andout temperature and
the converter outthe converter out
temperature sensor.temperature sensor.
FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
4455..0066 BB IInnvvaalliid d ppaatttteerrn n ffoor r tthhee
reduced vehiclereduced vehicle
speed redundantspeed redundant
digital inputs (2digital inputs (2
inputs used).inputs used).
The controller willThe controller will
limit the vehiclelimit the vehicle
speed to the reducedspeed to the reduced
speed.speed.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Invalid pattern for theInvalid pattern for the
reduced vehiclereduced vehicle
speed redundantspeed redundant
digital inputs (2digital inputs (2
inputs used).inputs used).
Check the redundantCheck the redundant
reduced vehiclereduced vehicle
speed switches andspeed switches and
the wiring connectedthe wiring connected
from these switchesfrom these switches
to the APC.to the APC.
4466..0055 AA TThhe e ttrraannssmmiissssiioonn
has exceeded thehas exceeded the
maximum torquemaximum torque
during inching.during inching.
The controller willThe controller will
open or close theopen or close the
inching clutchinching clutch
depending of thedepending of the
GDE parameterGDE parameter
selection.selection.
Release the inchingRelease the inching
pedal and cycle thepedal and cycle the
shift lever via neutralshift lever via neutral
back in the selectedback in the selected
direction in order todirection in order to
get drive again.get drive again.
The transmissionThe transmission
has exceeded thehas exceeded the
maximum torquemaximum torque
during inching.during inching.
Release the inchingRelease the inching
pedal and cycle thepedal and cycle the
shift lever via neutralshift lever via neutral
back in the selectedback in the selected
direction.direction.
To Next Page
Loading...
