Taylor TX360L - Page 171

TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
9C-229C-22
4477..0066 BB IInnvvaalliid d ppaatttteerrn n ffoor r tthhee
inching mode digitalinching mode digital
inputs (2 inputsinputs (2 inputs
used).used).
The controller willThe controller will
select the mode ”noselect the mode ”no
inching allowed”.inching allowed”.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Invalid pattern for theInvalid pattern for the
inching mode digitalinching mode digital
inputs (2 inputsinputs (2 inputs
used).used).
Check the inchingCheck the inching
mode selectionmode selection
switch and the wiringswitch and the wiring
connected from thisconnected from this
switch to the APC.switch to the APC.
5500..0000 SS AAnnaalloog g iinnppuut t 0 0 ((wwiirree
A11A11) related ) related fault :fault :
analog input isanalog input is
shorted to ground.shorted to ground.
Controller reverts toController reverts to
a ”limp home” mode.a ”limp home” mode.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI0 is below ANI0 is below 500500
ohm.ohm.
Check the wiringCheck the wiring
between the control-between the control-
ler and the pressureler and the pressure
feedback sensor.feedback sensor.
Check the pressureCheck the pressure
feedback sensor.feedback sensor.
5500..0011 SS AAnnaalloog g iinnppuut t 0 0 ((wwiirree
A11A11) related ) related fault :fault :
analog input is notanalog input is not
connected.connected.
Controller reverts toController reverts to
a ”limp home” mode.a ”limp home” mode.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI0 exceeds 4000ANI0 exceeds 4000
ohm.ohm.
Check the wiringCheck the wiring
between the control-between the control-
ler and the pressureler and the pressure
feedback sensor.feedback sensor.
Check the pressureCheck the pressure
feedback sensor.feedback sensor.
5511..0000 AA AAnnaalloog g iinnppuut t 1 1 ((wwiirree
A28) related A28) related fault :fault :
analog input isanalog input is
shorted to ground.shorted to ground.
The controller willThe controller will
limit the limit the transmissiontransmission
temperature mea-temperature mea-
surement to the low-surement to the low-
est clipped value inest clipped value in
its settings, whichits settings, which
will result in a badwill result in a bad
temperature com-temperature com-
pensation.pensation.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI1 is shortANI1 is shorted toed to
ground.ground.
Check the wiringCheck the wiring
between the control-between the control-
ler and the transmis-ler and the transmis-
sion sump tempera-sion sump tempera-
ture ture sensor. sensor. CheckCheck
the transmissionthe transmission
sump temperaturesump temperature
sensor.sensor.
5511..0011 AA AAnnaalloog g iinnppuut t 1 1 ((wwiirree
A28) related A28) related fault :fault :
analog input is notanalog input is not
connected.connected.
The controller willThe controller will
limit the limit the transmissiontransmission
temperature mea-temperature mea-
surement to the high-surement to the high-
est clipped value inest clipped value in
its settings, whichits settings, which
will result in a badwill result in a bad
temperature com-temperature com-
pensation.pensation.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI1 is not ANI1 is not con-con-
nected.nected.
Check the wiringCheck the wiring
between the control-between the control-
ler and the transmis-ler and the transmis-
sion sump tempera-sion sump tempera-
ture ture sensor. sensor. CheckCheck
the transmissionthe transmission
sump temperaturesump temperature
sensor.sensor.

FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
5522..0000 BB AAnnaalloog g iinnppuut t 2 2 ((wwiirree
A29) relateA29) related fault :d fault :
analog input isanalog input is
shorted to ground.shorted to ground.
Controller will flagController will flag
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settings.value in its settings.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI2 is shorANI2 is shorted toted to
ground, or measuredground, or measured
input value is belowinput value is below
the minimum valuethe minimum value
(corresponding with(corresponding with
0 %).0 %).
Check the wiringCheck the wiring
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
5522..0011 BB AAnnaalloog g iinnppuut t 2 2 ((wwiirree
A29) relateA29) related fault :d fault :
Controller will flagController will flag
the fault and will usethe fault and will use
Contact mainte-Contact mainte-
nance for troublenance for trouble
The analog inputThe analog input
ANI2 is notANI2 is not concon
Check the wiringCheck the wiring
between the controlbetween the control
https://www.forkliftpdfmanuals.com/