Taylor TX360L - Page 172

9C-239C-23TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
A29) relateA29) related fault :d fault :
analog input is notanalog input is not
connected.connected.
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settings.value in its settings.
nance for trouble-nance for trouble-
shooting.shooting.
ANI2 is not ANI2 is not con-con-
nected, or measurednected, or measured
input value is aboveinput value is above
the maximum valuethe maximum value
(corresponding with(corresponding with
100 %).100 %).
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
5533..0000 BB AAnnaalloog g iinnppuut t 3 3 ((wwiirree
B17) related fault :B17) related fault :
analog input isanalog input is
shorted to ground.shorted to ground.
Controller will flagController will flag
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settings.value in its settings.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI3 is shorANI3 is shorted toted to
ground, or measuredground, or measured
input value is belowinput value is below
the minimum valuethe minimum value
(corresponding with(corresponding with
0 %).0 %).
Check the wiringCheck the wiring
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
5533..0011 BB AAnnaalloog g iinnppuut t 3 3 ((wwiirree
B17) related fault :B17) related fault :
analog input is notanalog input is not
connected.connected.
Controller will flagController will flag
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settings.value in its settings.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI3 is not ANI3 is not con-con-
nected, or measurednected, or measured
input value is aboveinput value is above
the maximum valuethe maximum value
(corresponding with(corresponding with
100 %).100 %).
Check the wiringCheck the wiring
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
5544..0000 AA AAnnaalloog g iinnppuut t 4 4 ((wwiirree
B02) related fault :B02) related fault :
analog input isanalog input is
shorted to ground.shorted to ground.
Controller will flagController will flag
the fault. The control-the fault. The control-
ler uses the analogler uses the analog
input Ainput ANI4 to NI4 to have have aa
reference powerreference power
supply for the analogsupply for the analog
inputs ANI2, ANI3,inputs ANI2, ANI3,
ANI5 and AANI5 and ANI6.NI6.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The reference powerThe reference power
supply (4.5 V ref.) forsupply (4.5 V ref.) for
the analog inputsthe analog inputs
ANI2, AANI2, ANI3, ANINI3, ANI5 &5 &
ANI6 is belANI6 is below 4 Vow 4 V
Check the refenceCheck the refence
power supply of thepower supply of the
analog inputs ANI2,analog inputs ANI2,
ANI3, ANANI3, ANI5 andI5 and
ANI6.ANI6.

FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
5544..0011 AA AAnnaalloog g iinnppuut t 4 4 ((wwiirree
B02) related fault :B02) related fault :
analog input is notanalog input is not
connected.connected.
Controller will flagController will flag
the fthe fault. ault. The conThe con--
troller uses the ana-troller uses the ana-
log input ANI4 tolog input ANI4 to
have have a a referencereference
power supply for thepower supply for the
analog inputs ANI2,analog inputs ANI2,
ANI3, ANIANI3, ANI5 and5 and
ANI6.ANI6.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The reference powerThe reference power
supply (4.5 V ref.) forsupply (4.5 V ref.) for
the analog inputsthe analog inputs
ANI2, AANI2, ANI3, ANINI3, ANI5 &5 &
ANI6 is above 4.ANI6 is above 4.9595
VV..
Check the refenceCheck the refence
power supply of thepower supply of the
analog inputs ANI2,analog inputs ANI2,
ANI3, ANIANI3, ANI5 and5 and
ANI6.ANI6.
5555..0000 BB AAnnaalloog g iinnppuut t 5 5 ((wwiirree
B04) related fault :B04) related fault :
analog input isanalog input is
shorted to groundshorted to ground
Controller will flagController will flag
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settingsvalue in its settings
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI5 is shortANI5 is shorted toed to
ground, or measuredground, or measured
input value is belowinput value is below
Check the wiringCheck the wiring
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
https://www.forkliftpdfmanuals.com/