TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
9C-249C-24
shorted to ground.shorted to ground. value in its settings.value in its settings. input value is belowinput value is below
the minimum valuethe minimum value
(corresponding with(corresponding with
0 %).0 %).
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
5555..0011 BB AAnnaalloog g iinnppuut t 5 5 ((wwiirree
B04) related fault :B04) related fault :
analog input is notanalog input is not
connected.connected.
Controller will flagController will flag
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settings.value in its settings.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI5 is not ANI5 is not con-con-
nected, or measurednected, or measured
input value is aboveinput value is above
the maximum valuethe maximum value
(corresponding with(corresponding with
100 %).100 %).
Check the wiringCheck the wiring
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
5566..0000 BB AAnnaalloog g iinnppuut t 6 6 ((wwiirree
B06) related fault :B06) related fault :
analog input isanalog input is
shorted to ground.shorted to ground.
Controller will flagController will flag
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settings.value in its settings.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI6 is shortANI6 is shorted toed to
ground, or measuredground, or measured
input value is belowinput value is below
the minimum valuethe minimum value
(corresponding with(corresponding with
0 %).0 %).
Check the wiringCheck the wiring
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
5566..0011 BB AAnnaalloog g iinnppuut t 6 6 ((wwiirree
B06) related fault :B06) related fault :
analog input is notanalog input is not
connected.connected.
Controller will flagController will flag
the fault, and will usethe fault, and will use
the lowest clippedthe lowest clipped
value in its settings.value in its settings.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
The analog inputThe analog input
ANI6 is not ANI6 is not con-con-
nected, or measurednected, or measured
input value is aboveinput value is above
the maximum valuethe maximum value
(corresponding with(corresponding with
100 %).100 %).
Check the wiringCheck the wiring
between the control-between the control-
ler and the deviceler and the device
connected to thisconnected to this
analog analog input. input. CheckCheck
this device con-this device con-
nected. nected. Check if Check if thethe
calibration is donecalibration is done
correctly – recalibra-correctly – recalibra-
tion of this analogtion of this analog
input.input.
FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
6600..0000 SS//AA SSppeeeed d cchhaannnneel l 00
(wire A22) related(wire A22) related
fault : speed channelfault : speed channel
is shorted to ground.is shorted to ground.
When only 1 speedWhen only 1 speed
channel has a fail-channel has a fail-
ure, and which is noture, and which is not
the engine speedthe engine speed
channel, the control-channel, the control-
ler will calculate whatler will calculate what
the missing speedthe missing speed
should bshould be. e. If seIf severalveral
speed channelsspeed channels
have a failure, of thehave a failure, of the
engine speed chan-engine speed chan-
nel has a failure, thenel has a failure, the
controller reverts to acontroller reverts to a
”limp home” mode”limp home” mode
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Speed channelSpeed channel
SPC0 is shorted toSPC0 is shorted to
ground.ground.
Check the wiringCheck the wiring
between the control-between the control-
ler and the speedler and the speed
sensor connected tosensor connected to
speed channel 0.speed channel 0.
Check the speedCheck the speed
sensor connected tosensor connected to
speed channel 0.speed channel 0.
To Next Page
Loading...
