Taylor TX360L - Page 187

TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)9C-389C-38
no actions will beno actions will be
taken.taken.
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.
8811..0011 SS//AA DDiiggiittaal l oouuttppuut t 1 1 ((wwiirree
A15) related A15) related fault :fault :
output is shorted tooutput is shorted to
battery battery + + or the or the out-out-
put is not connected.put is not connected.
Action will depAction will dependend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical ou– critical output (eg.tput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Wire A15 is shortedWire A15 is shorted
to battery +.to battery +.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid: Check thesolenoid: Check the
wiring between thewiring between the
controller and thecontroller and the
Selector solenoid 8,Selector solenoid 8,
Check the selectorCheck the selector
solenoid solenoid 8. 8. If tIf thehe
output is connectedoutput is connected
to an other device:to an other device:
Check the wiringCheck the wiring
between the control-between the control-
ler and the otherler and the other
device, Check thedevice, Check the
other device.other device.
8822..0000 SS//AA DDiiggiittaal l oouuttppuut t 2 2 ((wwiirree
A16) related A16) related fault :fault :
output is shorted tooutput is shorted to
ground.ground.
Action will depAction will dependend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical ou– critical output (eg.tput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Wire A16 is shortedWire A16 is shorted
to ground.to ground.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid:solenoid:
Check the wiringCheck the wiring
between the control-between the control-
ler and the Selectorler and the Selector
solenoid 9, Checksolenoid 9, Check
the selector solenoidthe selector solenoid
9.9.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.

FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
8822..0011 SS//AA DDiiggiittaal l oouuttppuut t 2 (2 (wwiirree
A16) relateA16) related fault :d fault :
output is shorted tooutput is shorted to
battery + battery + or the or the out-out-
put is not connected.put is not connected.
Action will deAction will dependpend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical o– critical output (eg.utput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Wire A16 is shortedWire A16 is shorted
to battery +.to battery +.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid:solenoid:
Check the wiringCheck the wiring
between the control-between the control-
ler and the Selectorler and the Selector
solenoid 9, Checksolenoid 9, Check
the selector solenoidthe selector solenoid
9.9.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
https://www.forkliftpdfmanuals.com/