Taylor TX360L - Page 188

9C-399C-39TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
no actions will beno actions will be
taken.taken.
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.
8833..0000 SS//AA DDiiggiittaal l oouuttppuut t 3 (3 (wwiirree
A20) relateA20) related fault :d fault :
output is not con-output is not con-
nected, or shorted tonected, or shorted to
ground.ground.
Action will deAction will dependpend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical o– critical output (eg.utput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Wire A20 is shortedWire A20 is shorted
to ground.to ground.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid:solenoid:
Check the wiringCheck the wiring
between the control-between the control-
ler and the Selectorler and the Selector
solenoid 10, Checksolenoid 10, Check
the selector solenoidthe selector solenoid
10.10.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.
8833..0011 SS//AA DDiiggiittaal l oouuttppuut t 3 (3 (wwiirree
A20) relateA20) related fault :d fault :
output is shorted tooutput is shorted to
battery +.battery +.
Action will deAction will dependpend
on the functionon the function
assigned to the out-assigned to the out-
put:put:
– critical o– critical output (eg.utput (eg.
transmission valvetransmission valve
control): the control-control): the control-
ler reverts to a ”limpler reverts to a ”limp
home” mode.home” mode.
– non–critical f– non–critical featureeature
output: the controlleroutput: the controller
will flag the fault, butwill flag the fault, but
no actions will beno actions will be
taken.taken.
“limp home“ mode:“limp home“ mode:
Stop machine andStop machine and
go to neutral to bego to neutral to be
able to drive again.able to drive again.
”Limp home” mode”Limp home” mode
will result in reducedwill result in reduced
driving functionality.driving functionality.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Wire A20 is shortedWire A20 is shorted
to battery +.to battery +.
If the output is con-If the output is con-
figured as an outputfigured as an output
to a transmissionto a transmission
solenoid:solenoid:
Check the wiringCheck the wiring
between the control-between the control-
ler and the Selectorler and the Selector
solenoid 10, Checksolenoid 10, Check
the selector solenoidthe selector solenoid
10.10.
If the output is con-If the output is con-
nected to an othernected to an other
device: Check thedevice: Check the
wiring between thewiring between the
controller and thecontroller and the
other device, Checkother device, Check
the other device.the other device.

FaultFault
CCooddee TTyyppee EExxppllaannaattiioonn CCoonnttrroolllleerr’’s s AAccttiioonn DDrriivveer r AAccttiioonn FFaauullt t CCaauussee TTrroouubblleesshhoooottiinngg
90.xx90.xx
––
99.xx99.xx
S/B/S/B/
HH
SSyysstteem m EErrrroorr.. CCoonnttrroolllleer r rreevveerrtts s ttoo
a ”shut down” modea ”shut down” mode
and will force neutraland will force neutral
0.0.
Contact mainte-Contact mainte-
nance for trouble-nance for trouble-
shooting.shooting.
Software relatedSoftware related
fault.fault.
Contact Spicer Off–Contact Spicer Off–
Highway and informHighway and inform
the fault code andthe fault code and
the time that is wasthe time that is was
active.active.
9955..7711 SS DDaatta a iin n tthhe e AAPPC C iiss
not compatible withnot compatible with
the data expected bythe data expected by
the APC firmware.the APC firmware.
The controller revertsThe controller reverts
to a ”shut down”to a ”shut down”
mode and will forcemode and will force
neutral 0.neutral 0.
Download an APTDownload an APT
file compatible withfile compatible with
the active firmwarethe active firmware
into the APC.into the APC.
Wrong APT file (dataWrong APT file (data
file) is in the APCfile) is in the APC
(typically after APC(typically after APC
firmware upgrade).firmware upgrade).
Download an APTDownload an APT
file compatible withfile compatible with
the active firmwarethe active firmware
into the APCinto the APC
If the error code stillIf the error code still
persists, the datapersists, the data
fl h b tfl h b t
https://www.forkliftpdfmanuals.com/