Taylor TX360L - Drive Axle Troubleshooting; Differential overheats; Loss of oil out of the differential; Noisy differential

TX / TXH / TXB 180S - 400L (Rev. 4/23/07)TX / TXH / TXB 180S - 400L (Rev. 4/23/07)
14-414-4
DRAIN PLUGDRAIN PLUG
BLEEDERBLEEDER
VALVEVALVE
BREATHERBREATHER
Illustration 14-2. Illustration 14-2. Wet DWet Disc Brakes isc Brakes Drive Axle (TDrive Axle (TXH400L)XH400L)

Drive Drive Axle TroubleshooAxle Troubleshootingting
PPrroobblleemm CCaauussee CCoorrrreeccttiioonn
1.1. DiDifffefererentntiaiall
overheatsoverheats
1.1. LoLow ow oil il lelevvelel..
2.2. IncIncorrorrect ect typtype ane and grd grade ade of oof oil.il.
3.3. IncIncorrorrect ect beabearinring ag adjudjustmstmentent..
4.4. BreBreathather in er in difdifferferentential hial housousing iing iss
plugged.plugged.
5.5. OiOil ll levevel el is is totoo ho highigh..
1.1. FilFill to l to corcorrecrect let level vel witwith reh recomcom--
mended oil (refer to themended oil (refer to the Fuel andFuel and
Lubricant SpecificationsLubricant Specificationsin thein the
AppendicesAppendices).).
2.2. DraDrain, fin, fluslush, ah, and rend refilfill wil with rth recoecom-m-
mended oil.mended oil.
3.3. AdjAdjust ust beabearinrings. gs. RepReplaclace e any any thathatt
are damaged or excessively worn.are damaged or excessively worn.
4.4. RepReplaclace e breabreathether ir if f damdamageaged.d.
5.5. DraDrain oin oil dil down own to tto the che checheck pk pluglug
level in the differential.level in the differential.
2.2. LoLoss ss of of oioil ol out ut ofof
the differentialthe differential
1.1. DaDamamaged oged or badr badly wly wororn pinn pinioionn
shaft oil seal.shaft oil seal.
2.2. LooLoose se carcarrierier mr mounountinting bg boltolts.s.
3.3. BreBreathather in er in difdifferferentential hial housousing iing iss
plugged; forcing oil by the seals.plugged; forcing oil by the seals.
1.1. RepReplaclace oe oil sil seal eal and and checheck ck forfor
loose pinion bearings or pinion nut.loose pinion bearings or pinion nut.
2.2. CheCheck ack and tnd tighighten ten moumountinting bng boltolts.s.
Replace gasket if damaged or bro-Replace gasket if damaged or bro-
ken.ken.
3.3. RepReplaclace e breabreathether ir if f damdamageaged.d.
3.3. NoNoisisy y didiffffererenentitialal
a.a. NoNoisise oe on dn dririvvee a.a. RiRing geng gear aar and pnd pininioion adjn adjusust-t-
ment is too loose (excessive back-ment is too loose (excessive back-
lash).lash).
1)1) DriDrive ve shashaft ft is is outout-of-of-ph-phasease
aa.. AAddjjuusstt..
1)1) WheWhen tn the the tranransmismissission ton to axo axlele
drive shaft is installed, the flangesdrive shaft is installed, the flanges
on the drive shaft, must be alignedon the drive shaft, must be aligned
as shown in as shown in Illustration 1Illustration 11-1. 1-1. If theIf the
flanges are not aligned, repositionflanges are not aligned, reposition
https://www.forkliftpdfmanuals.com/