Technics RS-M27OX

r-
CASSETTE
INSERT!ON AND REMOVA
oFollow
the numbered order
@
!iltt u
Notes:
.Be
sure
the open
part
of the cassette
f
aces
downward. lf it is
upside down, the Cassette
Holder can't be closed.
oBe
sure
to
close
the
Cassette
Holder
gently.
oBe
careful
not to
press
the Eject Button while the tape
is
moving, because
this will
stop
the operation and the Cassette
Holder
will
open
TAPE
SELECTOB
Before beginning a
recording,
check
to be sure that the Tape
Selector
is
set
to the type of tape that is
going
to be used.
Note that there
may
be a difference
in
sensitivity of 2
or 3 dB
depending on
the type of tape
To open
the
cassette
tid.
((})
lt[!t0
!
o oEl
PLAYBACK
.Follow
the numbered
order.
E
power
push
on
F
The
lndicator lights
when the
power
is
switched on. But
it has
nothing to do with the Noise
Reduction Selector Switch
E-
o
qo
iln n
o
m[0!c !
o o
Refer
to
"CASSETTE
INSERTION AND
REMOVAL" above.
Tape
Selector
Settino
B rand
Tape Type
normal
AMPEX GFAND MASTEBI
BASF PBOFESSIONAL I
FUJI
FXI
MAXELL UD
MAXELL UDXLI
SCOTCH
MASTER
I
SONY
UHF
TDK AD
c-60, c-90
c-60,
c-90
c-60, c-90
c-60, c-90
c-60, c-90
c-60,
c-90
c-60, c-90
c-60 c-90
CrO,
AMPEX
GHAND
MASTERII
BASF PBOFESSIONAL
II
FUJI FX
II
MAXELL
UDXL II
SCOTCH
MASTEF tr
TDK
SA
c-60
c-60
c-60
c-60
c-60
c-46,
C-60
Metal
FUJI
SB
MAXELL MX
SCOTCH
IVIETAFINE
SONY
METALLIC
TDK
MA
c-46,
C-60, C-90
c-46,
C-60,
C-90
c-46,
c-60, c-90
c-46,
c-60.
c-90
c-46,
C-60.
C-90
C
[[![!L]
tape
select
Fe-Cr
CrOz
normal
Metal
Refer to
"TAPE"
SELECTOR" above
Set
the Noise Reduction
Switch
to
"Dolby
NR" when
using the Dolby system and to
"dbx
tape" when using
the dbx system
Refer
to
page
3 and 4
for instructions
on
use at the "dbx
disc"
position
n
play
[[[!!! r-
o
For
private
listening
4=="-o
lrllll I
o d.gs
!
For
listen-
ing
with
speakers
':" ':l
'rf,
"!,
*
,"ri"
!!. !r!
stop
Notes:
.Note
that the
operation buttons will not fuction
until about
5
seconds
have
passed
after the
power
rs
turned
on
.Output
is
0.42 V
f rom
the Line
Output Jacks
when the Output
Level
Control on this unit is set to its maximum
position
and
the Fluorescent Meter
scales
indicate
0
dB
.No
playback
sound will be heard from
this unit if,
during
playback,
the
Output
Level
Control
is set to its minimum
position,
even though the
volume
control of
the
amplifier
to
which this
unit
is
connected
is
set
to its maximum
position
oWhen
listening through headphones, adlust the volume level
by using the
Output
Level
Control
of this unit
.Do
not
set the Timer Start Switch to
"on"
during
playback
E