Technics SH-8016 - Page 2

‘We want to thank you ‘for selecting tl this product and
“to welcome you to the growing family of satisfied: é
Technics product owners around the world.
We feel certain you will get maximum enjoyment.
from this new addition to your home.
Please read these operating instructions carefully,
and be sure to keep them handy for convenient
reference.
e ACCESSORIES ;
eMAINTENANCE OF EXTERNAL SURFACES....... 2:
e@BEFORE USING THIS UNIT......................
eTECHNICAL SPECIFICATIONS . ;
eFOR SAFE USE OF THIS UNIT. 22°
STEREO SYSTEM COMPONENTS AND THEIR
CONNECTIONS .:...00. 0.000.000.5000 eee eee 4
eFRONT
PANEL
CONTROLS
AND
THEIR
nee
FUNCTIONS oo... 6 oie. cleseceeen elec ee ney 5
eTOTAL FREQUENCY! RESPONSE
eOPERATION:
-e@EXAMPLES OF APPLICATIONS UTILIZING
- THE SH-8016: FUNCTIONS.
- @TROUBLESHOOTING: GUIDE .
if the surfaces'are extremely
Use a minus (—) screwdriver to set the voltage selector (on the
‘rear panel) to the voitage setting for the area-in which the unit
will be used.
Note that this unit will be seriously damaged if this setting is not
made correctly. (There is no voltage selector for some coun-
tries; the correct voltage is already set.)
rl usea soft cloth, dipped pe
“asoap and water or.a weak detergent solution.
Wring the cloth well before wiping the unit:
‘Wipe once again witha soft dry cloth: = ‘ :
.Never use alcohol, paint: thinner, or benzine, nora Sha inically :
treated
cloth
to.
clean
this
unit.
:
:
euch chemicals may-mar the finish of your unit.
(DIN 45 500)
Frequency response
(center position)
Maximum output
voltage
Rated output voltage
Rated total harmonic
distortion
:5 Hz~100 kHz, —1 dB
:6V (1 kHz, THD 0.01%)
:1V
:0.005% (20 Hz~20 kHz)
0.003% (1 kHz)
vile V
:100 dB (110 dB, IHF’ A)
Input sensitivity
Signal-to-noise ratio
Maximum input
voltage >6V (1 kHz)
Input impedance 2:33 kO
Gain :0+1 dB
Channel balance
250 Hz~6300 Hz >+0.5 dB
Channel separation
1 kHz :70 dB
:+12 dB~-12 dB
(7 elements continuously variable
per channel) ,
:63 Hz, 160 Hz, 400 Hz, 1 kHz,
2.5 kHz, 6.3 kHz, 16 kHz
Band level controls
Center frequency
GENERAL
Power supply AC 50 Hz/60 Hz, 240 V
(For Australia)
AC 50 Hz/60 Hz, 110 V-127 Vie
220 V-240V
(For other areas)
Power consumption :7W
Dimensions. :
(HxWxD) :74.9x430x192.5 mm
(23%2"x 1616" xX 71%")
Weight > 1.95 kg (4.3 Ib)
Note:
Specifications subject to change without notice.
Weight and dimensions shown are approximate.
® Use a standard electrical AC wall outlet
. Use from an AC power source of high voltage, such as for air
conditioners, is very dangerous.
Be extremely careful not to make a connection to the elec-
trical outlet fora large air conditioner or central-heating unit
which uses high voltage, because there is the possibility of
fire.
2. ADC power source cannot be used.
Be sure to check the power source carefully, especially ona
ship or other place where DC is used.
-~