Technics SH-E5 Service Manual

10
11
12 13
14
15
16
D3,4
Q4
Q3
Ol
CIMAIIGOM
2SA968
2562238
g
SVDIB4B42
REGULATOR
REGUL
&
AXDic66
| GROUND
POINT
At
(VOLTAGE
SELECTOR)
A
ea
Bale
F4 T200m
ac
ov"
TTRED
200
S.A
gg
R57
‘4wi0
oN
:
AN
F2._7200mA
+
©)
z C57
25V 100
C55
(9)
BLK| A @ A
| AC 50/60HZ
AC
on
110/120/220/240V
YEL!
A
R58 14W 10
C56
He.
C58
25V 100
(POWER)
—15.2V LINE
et Notes:
D9 * The part No. of transistors, IC and diodes mentioned in the schematic diagram stand
for production part No. Regarding the part No. with © mark, the production part
L N224 WP No. are different from the replacement part No. Therefore, when placing an order for
POWER INDICATOR replacement parts, please use the part No. in the replacement parts list.
=
. This is the basic circuit diagram (For continental Europe) of this unit.
Note that part of the circuit is subject to change depending on the areas,
2. Regarding the circuits to be changed in the basic circuit diagram (For
continental Europe) and related areas [EK] , [EW] , [EGA] and [XL], refer to
speparated service manual (Order No. SD82062214 C8—A).
3. $1-1 ~ $1-2 : Tape monitor switch in “source” position.
source + tape
4, S$2-1 ~ $2-6 : Equalization position (position) switch in “source’’ position.
source @ rec out
5. S3-1 ~ $3-4 : Equalization (EQ) switch in “on” position.
6. SA : Power switch in “on” position.
7. $5 : Voltage selector switch in “220V” position.
110V + 120V « 220V © 240V
8. The R and L channels use the same circuit.
For the resistance and capacity of R channel, refer to the L channel.
9. Cc] Indicated voltage values are the standard values for the unit measured
by the DC electronic circuit tester (high-impedance) with the chassis taken as
standard. There fore, there may exist some errors in the voltage values, depending on
the internal impedance of the DC circuit tester.
10. Signal lines of left channel.
11, mmm = Positive (+B) voltage lines. =manp Negative (—B) voltage lines.
12. Important safety notice:
Componetns identified by A mark have special characteristics important
for safety. When replacing any of these components, use only manufacturer’s
specified parts.
a6
2SCl8I5
MUTING
PSA 1015 MA27\
MUTING
2
iC2878
ITCHING
25v220 + TF 25V220
Cil0 = =C210 C122 C222
102 C202
a 4
R202
I6Hz
R102
R502
C208 Cil2. 212 C116 C216
104 C204
t ve:
C108
+¥
R204 e Terminal guide of transistors, |C and diodes
31.5Hz
R104
SVITA75559S 2SA1015, 2SC1815, 2SA968, SVDIB4B42
28C2827 2SC2238
MOUs
R504
MA162A = LN224wP
as
a
eee
ee
ul
es
5
—Ta—
| 16Hz | Sil [31.512] Z| | 63Hz| l125Hz| | 250Hz| 1k Hz | | 2kHz | | &kHz_|
pr ey Cf Oe Ue Cb Ce UP Ue 7
20B

Technics SH-E5 Specifications

General

Brand	Technics
Model	SH-E5
Category	Recording Equipment
Language	English