Technics SL-P200 - Page 14

SL-P200 SL-P200
@ MN1554PEP (System Control)
Ro | wee otn | rami
Division
Sub-code block (Q data) clock input
(75Hz)
uo
Division
CLOSE Disc holder “Open” detection
Disc holder “Close” detection
processing LS!
)
TOC reading control (ON at “L”
(connected to GND)
Optical servo condition (focus)
input
Optical servo condition
{track cross) input
Data receipt command signal
Data transmission command
Data discrimination signal
Data lock signal
Key scan signal
Not connected
fs [ose
fs [Tent sre conan
Ec
(Not used, open)
CLK
DATA
STAT
Sub-code block (Q data) clock input
(7.35 kHz)
(Not used, open)
Sub-code (Q data) input
Reset signal input
OMP
(@) fe) 7) im Cc < i=] xz z r?) re) re)
x A
LOCK
a”
4
P20
5
37
P23
RECV
Not used (connected to +5V)
14 CLOSE Loading motor “Close” command
ACK
Loading motor “Open” command
SLOW (Not used, open)
a DATAO
44 | DATA3
17 MUTE Muting control
2) c
aad xz
Traverse servo control
(Not used, open)
Not connected se
2
Traverse “Reverse” command
signal
TRV.F Traverse “Forward” command
signal
Optical servo IC control signal
CNT4 (KICKR: Kick direction [reverse]
command)
Optical servo IC controi signal
CNT3 (KICKF: Kick direction [forward]
command)
Optical servo IC control
p26 | ONT fe) (TRON: Tracking servo)
VDD mae Power supply (connected to +5V)
Fo | (Not used, open)
| oO | (Not used, open)
Optical servo IC control signal
(FOON: Focus servo)
TRV.R
ap NTA
ie
z/z|=z/¢9 Flaolols SRILA
>| m
} 26 | Fe | JOUTON
| |
2 i=)
(?)
@ MN152611 (FL Drive and Timing Signal Generator)
0
Division
Optical servo condition input
(Not used, open)
0
Division
Remote control signal input
a (Not used, open)
Oc | (Not used, open)
(Not used, open)
(Not used, open)
| oO | (Not used, open)
VPP i FL drive power supply
Key scan signal
a
Ce
Fe [Prageno) [0 oan wns ommend oa
[ar Prrmecn [0 [one contconmana ane |
Pe [amie [© [rvesncnn |
Per |
37
©
¢
oO
(connected to —33V)
FL grid signal
(Not used, open)
FL grid signal
(Not used, open)
Reset signal input (reset at “L”)
Sub-code block (Q data) clock
(75Hz) input
(Not used, open)
Key return signal
FL grid signal
(Not used, open)
43 D4
5 5 FL grid signal
46 | D7
4 ri FL grid signal
49 DA (Not used, open)
Mi FL grid signal
- grid signa
DC
FL grid signal
(Not used, open)
FL anode signal
po | Power supply (connected to +5V)
Sub-code frame clock (7.35kHz)
SBT (Not used, open)
Sub-code Q data input
(Not used, open)
=
rie
P20
23
Key scan signal
5
24 vu
nN
ee elee
P40 pot Clock terminal
§ (Not used, connected to +5V)
31 | P42 Po Clock input