Need help?Do you have a question about the Technogym RUN EXCITE LIVE 9000 and is the answer not in the manual?
Remove plug immediately after use and before cleaning to reduce electric shock risk.
Take precautions against burns, fire, electric shock, or injury.
High voltage inside the product. Guard to be removed by authorised personnel only.
Enables viewing and managing workout/entertainment info, settings, and content.
Provide stable support when getting on/off or losing balance.
Turns red when product is in use, blinks at end of exercise.
Useful for walking with short steps.
Anti-static and shock-absorbing running surface.
For taking a short break due to fatigue or danger.
Enables changing treadmill belt speed and gradient during exercise.
Metal plate sensors that monitor heart rate.
Connects headphones for audio content.
NFC sensor or RFID reader for data interaction.
Universal Serial Bus port for data transfer or charging.
Reads workout data from Technogym key and saves results.
Holder for water bottles.
Provides ventilation during exercise.
Support for holding a phone.
Charges compatible devices wirelessly.
Step on from rear, place feet on foot rails, hold handgrip, set program.
Use side supports for initial safety, then let go for balance/posture.
Transition from walk to run, increase speed gradually, avoid distractions.
Hold side supports, place feet on foot rails, then step down.
In emergency, hold side supports firmly, step onto foot rails, then step down.
Remove power cable and store safely to prevent unchecked use.
Monitor via handgrip sensors or heart rate transmitter device.
Do not exceed 90% of max rate, not for medical diagnosis, avoid with pacemakers.
Use Qi-certified phones, position correctly, remove thick cases, do not leave unattended.
Avoid objects between phone/charger, keep magnetic cards away, use for intended purposes.
Provides dimensions (length, width, height) and weight of the product.
Compares specifications across different models (9000, 7000, 5000, 900, 700, 500).
Details power supply, motor power, noise level, speed ranges, and input power.
Classified as SB device, designed for indoor use in residential/professional environments.
Allows stopping the treadmill belt without using controls.
Cord with clip to attach to clothing for emergency stops.
Connects and disconnects the product's power.
Protects electrical parts from excessive current.
Marks on belt indicate if it is moving.
Red light on left support indicates the treadmill belt is moving.
Stops belt if no person is detected for 30s at speeds >= 3 km/h.
Contains important safety warnings regarding usage and hazards. Do not remove.
Turn on by pressing the switch to the 'I' (ON) position.
Turn off by pressing the main switch to the '0' (OFF) position.
Switch does not isolate from mains voltage; unplug to isolate.
Requires specific temperature, air circulation, lighting, and free space.
Avoid direct sunlight, humid environments, outdoors, water jets, spray products, interference.
Lift slightly using handle (T), push forwards/backwards. Requires more than one person.
Move carefully; product can be unstable and tip over. Use handle (T) only.
Remove panel, loosen lock nut, turn foot (D) with wrench to level.
Plug cable into product, then into wall socket. Ensure socket is accessible.
Use bracket (S) to secure cable, tie excess length.
Socket must have earth. Grounding reduces electric shock risk.
Improper earthing risks electric shock; use qualified electrician.
Connects antenna using an RF coaxial cable with F-type connector.
Ethernet port for network connectivity.
Connected devices must comply with international standards.
Inspect every two weeks for damage/wear. Replace or remove from service if defective.
Disinfect hand sensors after each use if used for medical purposes.
Check monthly for condition and functionality of emergency switch and STOP button.
Turn off, unplug, clean display with a damp (not wet) cloth.
Clean outer parts with damp sponge, belt area with vacuum cleaner weekly.
Do not use chemical products/solvents. Wipe display/labels carefully.
Periodic maintenance, adjustment, lubrication must be done by Technogym Technical Support Service.
Check belt wear (A), clean motor compartment (B), check drive belt (C).
Green light indicates belt wear state: steady ON = no maintenance, blinking = wear shown.
Adjust tension screw with wrench to align belt mark to reference points (B).
Check power, cable connection, and circuit breaker status.
Check leveling, bearings, belt wear, and belt centering.
Offers telephone consultation, warranty info, on-site servicing, spare parts.
Provide product model (A), date of purchase, serial number (B), and problem description.
Unauthorized work by persons not approved by Technogym will invalidate the warranty.
Store in a clean dry place, with a dust cover, at room temperature and humidity.
Do not dispose in environment. Use specialized firms. Follow EU/local regulations.
To Next Page
General