TECNICOMAR ECOmar S Series

Questions and Answers

E
Emily GriffithAug 18, 2025
Why does my TECNICOMAR ECOmar S Water Dispenser system shut down for OVERLOAD ALARM fault?
- B
  barbarawalkerAug 18, 2025
  The TECNICOMAR Water Dispenser system might shut down due to an overload alarm for several reasons: 1. The black switch button of the circuit switch breakers may be wrongly set. Ensure it is in the ON position, pressed inside the switch circuit breaker. 2. Circuit switch breakers keep tripping, indicating a system short circuit that needs to be resolved. 3. The power supply voltage may be incorrect. Power the plant with a voltage suitable to that indicated on the system nameplate, or replace the ECOmar S STP with one suitable for the power supply line voltage. 4. A broken control box can also cause this issue; in this case, it should be repaired or replaced.
N
Nancy SantiagoAug 20, 2025
Why does my TECNICOMAR ECOmar S system shut down for FILLING ALARM fault?
- B
  Brendan GonzalesAug 20, 2025
  The system may shut down due to a filling alarm fault because of: 1. A malfunctioning Min. Level Sensor of the Treatment Tank. To resolve this, clean the level sensor and reinstall it. 2. Malfunctioning Filling Pump. Open all the valves installed along each filling pump suction / delivery piping. 3. A broken control box. If this is the case, repair or replace the main control box.
N
nicolejonesAug 23, 2025
Why does my TECNICOMAR ECOmar S Water Dispenser system shut down for SEAWATER ALARM fault?
- C
  Connie TurnerAug 23, 2025
  The TECNICOMAR Water Dispenser system might shut down due to a seawater alarm fault for these reasons: 1. A malfunctioning Max. Level Sensor of the Treatment Tank. Clean the level sensor and re-install it. 2. A malfunctioning Seawater Pump. Open all the valves installed along seawater pump suction piping. 3. A broken control box. If this is the problem, repair or replace the main control box.
J
Jordan SimonAug 26, 2025
What to do if TECNICOMAR ECOmar S Water Dispenser has excessive noise and vibrations?
- T
  Timothy DawsonAug 26, 2025
  If your TECNICOMAR Water Dispenser is exhibiting excessive noise and vibrations, consider the following: 1. **System pulsation**: Check the Filling /Seawater pump correct priming and the presence of any leaks or restrictions on their suction piping, and correct it. 2. **Worn seals**: Replace pumps (filling, seawater, macerating) seals. 3. **Air presence**: Pressurize the affected circuit (filling, seawater, sludge discharge, clarified water discharge), by filling it activating the relative pump. This will help to eliminate the infiltrated air.
K
Kelsey MeyerAug 28, 2025
Why does my TECNICOMAR ECOmar S Water Dispenser system shut down for HIGH PRESSURE ALARM fault?
- D
  donaldgonzalezAug 28, 2025
  The TECNICOMAR Water Dispenser system may shut down due to a high-pressure alarm fault due to: 1. Wrong settings of the black switch button of the circuit switch breakers. Set the black switch button of the circuit switch breakers, in ON position, with the switch button pressed inside the switch circuit breaker. 2. Wrong or inefficient ventilation of the treatment tank. Remove any obstructions from the air relief and vent line, ensuring they are as free as possible. 3. A broken control box. If this is the case, repair or replace the main control box.
L
Lauren HuntAug 30, 2025
What to do if my TECNICOMAR ECOmar S treated and discharged water are dark?
- L
  Lauren HooperAug 31, 2025
  If the treated and discharged water from your TECNICOMAR Water Dispenser is dark, check the following: 1. **H2O Dosing System**: Set the Dosing Timer parameter and the dosing pump flow regulation to the correct values shown on the attached Test Report. 2. **Safe filter**: If necessary, empty and clean the bag cartridge or replace it. 3. **Discharge Timer parameter**: Adjust the Discharge Timer parameter setting value according to the plant on board installation condition.
T
Thomas RushSep 1, 2025
What to do if TECNICOMAR ECOmar S Water Dispenser unit is powered correctly but does not start?
- V
  victoriaadamsSep 2, 2025
  If the TECNICOMAR Water Dispenser unit is powered correctly and set in automatic mode, with 'System Running' displayed, but it doesn't start, consider these potential issues: 1. **Collecting Tank Level Probes malfunctioning**: Ensure each supplied sensor is correctly installed and connected, referring to the attached connections diagrams. 2. **Level Probe Control Box malfunctioning**: Repair or replace each supplied level probe control box. 3. **Broken control box**: Repair or replace the main control box.
T
Tracy MooreSep 4, 2025
How to fix no or low quality visualization on the TECNICOMAR ECOmar S STP display?
- K
  Kelli DavisSep 5, 2025
  If there is no or low-quality visualization on the display of your TECNICOMAR ECOmar S STP, consider the following: 1. **Display contrast calibration**: Re-calibrate the display contrast by acting on the trimmer P2 installed on the rear side of the P.C.B. PRO14. 2. **Display backlight settings**: Set properly the “Display Backlight Timer” parameter. 3. **Broken control box**: Repair or replace the main control box.
S
Stephanie MackSep 7, 2025
What to do if TECNICOMAR Water Dispenser Sludge Discharge Valve (V2) does not open or close?
- J
  Jason BrownSep 7, 2025
  If the Sludge Discharge Valve (V2) on your TECNICOMAR Water Dispenser does not open or close, it could be due to: 1. A malfunctioning Motorized valve. Set the rotation direction of the actuator to Y2. 2. A broken control box. If this is the cause, repair or replace the main control box.
C
Craig GoodSep 9, 2025
What to do if TECNICOMAR ECOmar S Water Dispenser Discharge Valve (V1) does not open or close?
- M
  Ms. Emily HoSep 10, 2025
  If the Discharge Valve (V1) on your TECNICOMAR Water Dispenser does not open or close, consider: 1. A malfunctioning Motorized valve. Set the rotation direction of the actuator to Y2. 2. A broken control box. If this is the cause, repair or replace the main control box.