TECO E710-403-H3SF - Group 17: Automatic Tuning Parameters

57
Group 16: LCD Function Parameters
Code
Parameter
Name
Setting Range Default
Attrib
ute
inverter and
operator.
16-08
Selection of
Allowing
Reading
0: Do not allow
to read inverter
parameters and
save to the
operator.
0
1: Allow to read
inverter
parameters and
save to the
operator.
16-09
Selection of
Operator
Removed
(LCD)
0: Keep
operating
when LCD
operator is
removed.
0 *1
1: Display fault
when LCD
operator is
removed
16-10
RTC Time
Display Setting
0: Hide
0 Note8
1: Display
16-11
RTC Date
Setting
12.01.01 ~
99.12.31
12.01.0
1
Note8
16-12
RTC Time
Setting
00:00 ~ 23:59 00:00 Note8
16-13
RTC Timer
Function
0: Disable
1: Enable
2: Set by DI
0 Note8
16-14 P1 Start Time 00:00 ~ 23:59 08:00 Note8
16-15 P1 Stop Time 00:00 ~ 23:59 18:00 Note8
16-16 P1 Start Date
1:Mon
2:Tue
3:Wed
4:Thu
5:Fri
6:Sat
7:Sun
1 Note8
16-17 P1 Stop Date 5 Note8
16-18 P2 Start Time
00:00 ~ 23:59
08:00 Note8
16-19 P2 Stop Time
00:00 ~ 23:59
18:00 Note8
16-20 P2 Start Date
1:Mon
2:Tue
3:Wed
4:Thu
5:Fri
6:Sat
7:Sun
1 Note8
16-21 P2 Stop Date 5 Note8
16-22 P3 Start Time 00:00 ~ 23:59 08:00 Note8
16-23 P3 Stop Time 00:00 ~ 23:59 18:00 Note8
16-24 P3 Start Date
1:Mon
2:Tue
3:Wed
4:Thu
5:Fri
6:Sat
7:Sun
1 Note8
16-25 P3 Stop Date 5 Note8
Group 16: LCD Function Parameters
Code
Parameter
Name
Setting Range Default
Attrib
ute
16-26 P4 Start Time 00:00 ~ 23:59 08:00 Note8
16-27 P4 Stop Time 00:00 ~ 23:59 18:00 Note8
16-28 P4 Start Date
1:Mon
2:Tue
3:Wed
4:Thu
5:Fri
6:Sat
7:Sun
1 Note8
16-29 P4 Stop Date 5 Note8
16-30
Selection of
RTC Offset
0: Disable
0 Note8
1: Enable
2: Set by DI
16-31
RTC Offset
Time Setting
00:00 ~ 23:59
00:00 Note8
16-32
Source of
Timer 1
0: None, 1:P1,
2:P2, 3:P1+P2
4:P3, 5:P1+P3,
6:P2+P3,
7:P1+P2+P3,
8:P4, 9:P1+P4,
10:P2+P4,
11:P1+P2+P4
12:P3+P4
13:P1+P3+P4,
14:P2+P3+P4
15:P1+P2+P3+
P4,
16:Off,
17:Off+P1
18:Off+P2,
19:Off+P1+P2
20:Off+P3,
21:Off+P1+P3
22:Off+P2+P3
23:Off+P1+P2+
P3
24:Off+P4
25:Off+P1+P4
26:Off+P2+P4
27:Off+P1+P2+
P4
28:Off+P3+P4
29:Off+P1+P3+
P4
30:Off+P2+P3+
P4
31:Off+P1+P2
+P3+P4
1 Note8
16-33
Source of
Timer 2
2 Note8
16-34
Source of
Timer 3
4 Note8
16-35
Source of
Timer 4
8 Note8
16-36
Selection of
RTC Speed
0: Off
0 Note8
1: By Timer 1
2: By Timer 2
3: By Timer 3
4: By Timer 4
5: By Timer
1+2
16-37
xxx0b: RTC
Run1
0000b Note8