Tecumseh HM90 User Manual

REMOVING TOW BAR
Attacr. tnls enc
to tra~:lr
E
,
13
Lodt
, Wasner
Holes ,n front
01 frame
"'-,
\ Hex Nut
\.
\
Flat
Washer
Tow Bar
Base
r
!
Axle
Position
"'.,
~
/
Chipper
Shrender
Frame
Attacn thIS enc
to CnJooer snrea:::!!~
Figure 5:
Figure 4:
Figure 3:
Remove the cleVIS Din arc the sanng plr,
attaching me tow oar tongue 10 tne Irac:o~. -
Remove the ionger cievls Din ana tne scnng pin
attaching
tne tow oar tongue Ie me tow oar case and
cull the tongue
aut at tne oase. v::.; may '<eeo the
tow bar base attached to the C:1lccer snreaaer.
If you had aralned the engme c; 0:1 ar.: ;asollne
for ~ransDortlng the UniL ~efiii Wli~ ~res~ :;:1 anc gas
DeTore oDeratmg me 'Jnr:.
a If the wheel axle on your :ntcper snrecder unit
goes through the fromupperno Ie on tne side of
'the frame, place the tow car In cosition 50 the
axle IS inside the tow barbase.
b.
If the wheel axle on your cntpcer shreader
goes through the rear lower ~Ole OT'! the side
of the frame. place the tow car case In
position so the axle is uneemeath me tow
bar base.
Select the hole in the tow bar base whicn aligns
with
the right front engine mounting bott. ana
:Jlace base over oolt.
Place lock washer over bott wrth the cupoea side
of the washer against the tow car case (crowned •
side
will go against the nex nut).
Thread the hex nut onto the c:~lt very looseiy; do
not tighten at this time.
Check the front of the shredder frame.
a. If
two noies are already provlaeo on the
frame, proceea to next steo.
b. If there are no holes on the frame. Dress the
tow bar oass against me trame. :lg:"1ten the
nut on the r;ght tront engine COlt. ana drill two
13/32" hOles using the tow car as a gUlae.
Place flat wast,ers on hex botts.
Insert
hex colt (with washer) into the hOle from
InSlae
the smecder trame. ana througn ~he tow
bar base.
If the axle IS inside the tow car case. you may
need to place the flat wasner against the shredder
frame. then inser. the bOlt througn tne washer.
frame and the tow bar case.
Secure with laCK wasner ana nex :1ut on the front
of the tow bar base. Do not tlgnten at ' .... 0; :--,"t.
Repeat with other nex bolt. Do not t;
Press the tow bar base firmly agam~. .~. Ilpper
shredder frame. ana tlgnten co~n sets ~: : ;)Its and
nuts holding the tront of the tow car case. See
Figure
5.
Tignten the engine mounting :011 an: nut that you
haa eartier removed. .
Place the tow bar tongue InSlee me tow c~r base.
Align the holes ant secure with snorrer :levls pm
ana one spring pm.
Use the ionger CleVIS Din ana tne scnng pm to
attach
the chipper shredderto your lawn tractor.
See
Figure 5.
•
•
•
•
•
•
•

Tecumseh HM90 Specifications

General

Brand	Tecumseh
Model	HM90
Category	Engine
Language	English