Command Groups
2β20
TDS Family Oscilloscope Programmer Manual
Measurement commands can set and query measurement parameters. You can
assign some parameters, such as waveform sources, differently for each
measurement readout. Other parameters, such as reference levels, have only one
value, which applies to all measurements.
Table 2β14: Measurement Commands
Header Description
ξξξξξ%ξ!ξ"'ξ Return all measurement parameters
ξξξξξ%ξ!ξ"'ξξξξξξξξξ$&ξ#' Take down measurement snapshot
ξξξξξ%ξ!ξ"'ξξξξξξξ Set or query measurement gating
ξξξξξ%ξ!ξ"'ξξξξξξξ Return immediate measurement parameters
ξξξξξ%ξ!ξ"'ξξξξξξξξξξξ*ξ Return info on immediate delay measurement
ξξξξξ%ξ!ξ"'ξξξξξξξξξξξ*ξ
ξξξξξ' #"
Search direction to use for delay measure-
ments
ξξξξξ%ξ!ξ"'ξξξξξξξξξξξ*ξξξξξξ Which waveform edge to use for delay
measurements
ξξξξξ%ξ!ξ"'ξξξξξξξξξξξ*ξξξξξξ Which waveform edge to use for delay
measurements
ξξξξξ%ξ!ξ"'ξξξξξξξξξξξξξξξξ Channel to take measurement from
ξξξξξ%ξ!ξ"'ξξξξξξξξξξξξξξ Second channel to take measurement from
(delay or βtoβ channel)
ξξξξξ%ξ!ξ"'ξξξξξξξξξξξ The measurement to be taken
ξξξξξ%ξ!ξ"'ξξξξξξξξξξ'&ξ Return measurement units
ξξξξξ%ξ!ξ"'ξξξξξξξξξξ(ξξ Return measurement result
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξ Return parameters on measurement
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξξ*ξ Return delay measurement parameters
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξξ*ξ
ξξξξξ' #"
Search direction to use for delay measure-
ments
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξξ*ξξξξξξ Which waveform edge to use for delay
measurements
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξξ*ξξξξξξ Which waveform edge to use for delay
measurements
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξ ξξξξξξξξξ Channel to take measurement from
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξξξξξ Second channel to take measurement from
(delay or βtoβ channel)
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξξξ Turn measurement display on or off
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξξ The measurement to be taken
ξξξξξ%ξ!ξ"'ξξξξξξ
)ξξξξξ'&ξ Return units to use for measurement
To Next Page
Loading...
Need help?
General
