Index
Index–12
TDS 500B, TDS 600B, & TDS 700A User Manual
Reference Indicator, Channel, 3–8
Reference levels, 2–21
Defining for Measure, 3–97
Reference Levels, Measure menu, 3–97
Reference memory, Glossary–9
Reject Glitch, Main Trigger menu, 3–76
Remote communication, 3–134–3–138
Remote operation
Communicating with Remote Instruments, 3–134
Connecting to the GPIB, 3–136
GPIB interface requirements, 3–134
GPIB Protocols, 3–134
Interconnect cabling, 3–135
Preparation for, 3–134
Procedures for, 3–135
Selecting and configuring the port, 3–136
Remove Measrmnt, Measure menu, 3–95, 3–99
Rename, File Utilities menu, 3–123
Repetitive Signal, Acquire menu, 3–25
Reset, How to execute, 3–8
Reset All Mappings To Factory, Color menu, 3–38
Reset All Palettes To Factory, Color menu, 3–38
Reset Current Palette To Factory, Color menu, 3–38
Reset to Factory Color, Color menu, 3–36
Reset Zoom Factors, Zoom menu, 3–42
Restore Colors, Color menu, 3–38
Ring Bell if Condition Met, Acquire menu, 3–146
Rise time, 2–20, 3–93, Glossary–9
Rising edge, Delayed Trigger menu, 3–89
Rising edge, Main Trigger menu, 3–62, 3–70, 3–71
RLE Color, Hardcopy menu, 3–127
RMS, 3–93, Glossary–9
RS-232, 2–5
RS-232, Port, 3–128, 3–134
RS232C/Centronics Hardcopy Interface, Option 13,
A–2
RUN/STOP, 3–50
RUN/STOP, Acquire menu, 3–27
Runt trigger, 3–73, 3–74, Glossary–9
How to set up, 3–77–3–90
Runt, Main Trigger menu, 3–77
S
Sample acquisition mode, 3–21, Glossary–9
Sample interval, Glossary–9
Sample Rate
Maximum, 3–21
Option 1G, A–1
Sample, Acquire menu, 3–24, 3–25
Sampling, 3–18, Glossary–10
Sampling and acquisition mode, 3–25
Sampling and digitizing, 3–17
Saturation, Color menu, 3–36
Save, Setups, 3–115
Save Current Setup, Save/Recall Setup menu, 3–115
Save Format, Save/Recall Waveform menu, 3–119
Save Waveform, Save/Recall Waveform menu, 3–118
Save/Recall SETUP button, 2–10, 3–8, 3–115, 3–122
Save/Recall Setup menu, 3–115
factory status, 3–116
File Utilities, 3–117
Recall Factory Setup, 3–117
Recall Saved Setup, 3–116
Save Current Setup, 3–115
user status, 3–116
Save/Recall WAVEFORM button, 3–118, 3–122
Save/Recall Waveform menu, 3–118
active status, 3–118
Autosave, 3–121
Delete Refs, 3–120
empty status, 3–118
File Utilities, 3–121
Ref1, Ref2, Ref3, Ref4, File, 3–120
Save Format, 3–119
Save Waveform, 3–118
Saving, Waveforms, 3–118
Saving and recalling setups, 2–24, 3–115
Saving and recalling waveforms, 3–118
Saving Waveforms and Setups, 3–115
Scale, vertical, 3–159, 3–170, 3–175
seconds, Cursor menu, 3–105
Security bracket, 2–5
SELECT button, 3–104, Glossary–10
Select Measrmnt, Measure menu, 3–94, 3–98
Selected waveform, Glossary–10
Self test, 1–6
Serial number, 2–5
Service Assurance, A–7
Set 1st Source to, More menu, 3–149
Set 2nd Source to, More menu, 3–149
Set Function to, More menu, 3–149
SET LEVEL TO 50% button, 3–56
Set Levels in % units, Measure menu, 3–97
Set operator to, More menu, 3–149
Set Single Source to, More menu, 3–148, 3–149
Set Thresholds, Main Trigger menu, 3–67, 3–70
Set to 10%, Horizontal menu, 3–17
Set to 50%, Delayed Trigger menu, 3–89
Set to 50%, Horizontal menu, 3–17
Set to 50%, Main Trigger menu, 3–56, 3–62, 3–76,
3–84
Set to 90%, Horizontal menu, 3–17
Set to ECL, Delayed Trigger menu, 3–89
To Next Page
Loading...
Need help?
General
