TensCare Unipro - User Manual

Questions and Answers

J
Jessica BruceAug 13, 2025
What to do if intensity setting returns to 0mA on TensCare Unipro?
- K
  Kimberly CurryAug 13, 2025
  If the intensity setting on your TensCare Fitness Equipment returns to 0mA, it indicates a connection error, leading to an open circuit. Ensure the pads are correctly attached to your body and the lead wire is properly inserted into both the pads and the device. Alternatively, faulty pads or lead wires could be the issue. Try using the other lead wire or electrode pads. If the problem persists, you may need to purchase replacements.
A
allenturnerAug 17, 2025
Why no sensation with TensCare Unipro?
- Q
  qcarterAug 17, 2025
  If you're not feeling any sensation with your TensCare Fitness Equipment, the intensity might not be strong enough. Increase the intensity until you feel a strong but comfortable sensation.
M
michelle69Aug 20, 2025
How to unlock TensCare Unipro controls?
- J
  Jamie SchmidtAug 21, 2025
  If the controls on your TensCare Fitness Equipment aren't working, the keypad might be locked. If you see the lock icon, press either of the - buttons to unlock the device.
T
Timothy JenningsAug 25, 2025
Why won’t intensity increase above 40mA on TensCare Unipro Fitness Equipment?
- S
  sharonreynoldsAug 25, 2025
  If the intensity setting on your TensCare Fitness Equipment won’t increase above 40mA while using IFT mode, it's a safety feature to prevent harm. To increase it up to 60mA, press the phase skip button. This disables the intensity lock, allowing you to increase the intensity.
L
Lindsey TorresAug 28, 2025
What does flashing warning icon mean on TensCare Unipro?
- J
  jonathanandersonAug 28, 2025
  If you see a flashing warning icon on your TensCare Fitness Equipment, the EMS manual mode WORK/REST settings have been adjusted outside the recommended ratio. Continue treatment with caution and stop if the stimulation becomes uncomfortable. You can reset the manual programme settings by pressing and holding the mode and programme buttons simultaneously.
T
Todd HicksSep 1, 2025
What to do for low battery display on TensCare Unipro Fitness Equipment?
- A
  Andrew RochaSep 1, 2025
  If your TensCare Fitness Equipment displays a low battery warning, it means the battery is low. Charge the battery.
J
Jose BrownSep 5, 2025
Why can't I access TENS, EMS, or MIC modes on TensCare Unipro?
- J
  James CarterSep 5, 2025
  If you cannot access TENS, EMS, or MIC modes on your TensCare Fitness Equipment, it's likely because the device is connected to the mains power supply. Disconnect the device from the charging adapter and restart it. Then, access the desired mode and programme.
J
Jenna BarnettSep 9, 2025
How to fix no display on TensCare Unipro Fitness Equipment?
- K
  kylecontrerasSep 9, 2025
  If your TensCare Fitness Equipment has no display, it could be due to a flat battery. Charge the battery. If the battery is damaged, contact the supplier.

Summary

01. Introduction

Intended Use

Defines the Unipro as a multitherapy medical device and its applications.

02. Contents

The Pack Contains

Lists all the items included in the Unipro device package.

03. Safety Guidelines

Contraindications

Details conditions and situations where the device should not be used.

Warnings

Highlights critical safety precautions and potential risks associated with device use.

Cautions

Outlines precautions and potential risks to be aware of during device operation.

Electrode Pad Cautions

Provides specific safety advice regarding the use and placement of electrode pads.

04. Unipro Device

Device Operation Controls

Covers power, intensity adjustment, mode, programme, and settings controls.

Device Icons and Indicators

Explains warning icons, connection error icons, and keypad lock indicators.

Phase Skip and Lock Functionality

Details phase skip for EMS and keypad lock/unlock features.

05. Directions for Use

Connecting Lead Wires and Pads

Step-by-step guide for connecting wires and applying electrode pads.

Turning the Device On

Instructions on how to power on the Unipro device.

Mode and Programme Selection

Guide to selecting operating modes and programmes.

Selecting Treatment Time

How to adjust the treatment duration for programmes.

Setting the Intensity

Instructions for adjusting stimulation intensity levels.

Manual Setting Selection

Details on selecting and changing manual programme parameters.

Completing a Session

Guidance on what happens during and after a treatment session.

After Your Session

Steps to take after completing a treatment session, including pad removal.

Usage Memory

How to view and reset device usage memory.

06. TENS Programmes

Pain Gate

Explains the Pain Gate stimulation method for pain relief.

Endorphin Release

Describes Endorphin Release TENS for natural pain relief.

Programme Selection

Advice on selecting the most suitable TENS programme.

Intensity Selection

Guidance on adjusting intensity for TENS programmes.

Frequency of Use

Recommendations on how often and for how long TENS can be used.

07. EMS Programmes

EMS Modes

Details the different EMS modes: EMS I, II, III, and IV.

EMS Programme Applications

Describes programmes for Muscle Calming, Resume Training, and Resistance Training.

EMS Programme Applications (Continued)

Details programmes for Resistance Training, Lipolysis, Muscle Contraction, and Toning.

Manual EMS Programmes

Information on manual programmes for custom settings.

08. IFT Programmes

IFT Therapy Explanation

Explains how Interferential Therapy (IFT) works and its benefits.

IFT Modes: IFT4 and IFT2

Describes the two IFT modes and their pad requirements.

Programme Selection for IFT

Guidance on choosing the right IFT programme.

Intensity Selection for IFT

Details on adjusting intensity and safety limits for IFT.

09. Microcurrent Programmes

Microcurrent Therapy Explanation

Explains Microcurrent Stimulation (MIC) and its benefits.

Programme and Setting Selection for MIC

Advice on selecting frequencies and settings for Microcurrent programmes.

Microcurrent Usage Advice and Settings

Tips and advice for optimizing Microcurrent therapy results.

10. Pad Placement

TENS and EMS Pad Placement

Guidance on positioning electrode pads for TENS and EMS therapies.

IFT Pad Placement

Instructions for placing electrode pads for IFT modes.

MIC Pad Placement

Guidance on electrode pad positioning for Microcurrent therapy.

Specific Pad Placement and Advice

Specific examples for arm pain and general pad advice.

11. Other Functions

Language Selection and Usage Memory

How to select the device's language and manage usage memory.

12. Charging Unipro

Battery Charging and Adapter Safety

Instructions for charging the battery and warnings about adapter use.

Battery Specifications and Warnings

Details charging specs, and critical warnings for battery safety.

13. Cleaning & Storage

Cleaning and Storage Instructions

Guidance on how to clean and store the Unipro unit and its accessories.

14. Replacement Parts

Service Life and Ordering Parts

Information on device lifespan, accessory life, and how to order replacement parts.

15. Warranty

Warranty Terms and Service Procedures

Details the product warranty coverage and procedures for returning for service.

16. Troubleshooting

Common Issues and Solutions

A guide to identifying and resolving common problems with the Unipro device.

17. EMC

Electromagnetic Emissions and Precautions

Discusses wireless equipment effects and EMC precautions.

Declaration - Electromagnetic Emission

Details compliance for RF emissions and harmonic emissions.

Declaration - Electromagnetic Immunity

Outlines immunity levels for ESD, surge, and voltage variations.

Declaration - IMMUNITY to proximity fields from RF wireless communications equipment

Specifies immunity levels for RF proximity fields.

18. Disposal of Electronic Products (WEEE)

WEEE Disposal Guidelines

Instructions for responsibly disposing of the device according to WEEE regulations.

19. Technical Specification

TENS and EMS Programme Parameters

Detailed technical specifications for TENS and EMS programmes.

IFT and Microcurrent Programme Parameters

Technical specifications for IFT and Microcurrent programmes.

Device General Specifications

Overall device specifications including output, channels, battery, and weight.

Environmental and Safety Specifications

Details operating conditions, storage, and safety classifications.

Symbols Table

Explanation of various symbols used on the device and in the manual.

Device Identification and Safety Symbols

Definitions of serial number, CE mark, medical device symbols, and safety warnings.

EC Declaration of Conformity

Product Compliance Statement

Declaration of conformity with EU regulations for medical devices.

TensCare Unipro Specifications

General

Brand	TensCare
Model	Unipro
Category	Fitness Equipment
Language	English

Related product manuals

TensCare Perfect PFE

36 pages

TensCare Elise 2