Textron Greenlee 1818 - 1-1;4 IMC;RIGID Data; 1-1;2 IMC;RIGID Data

Greenlee / A Textron Company 16 4455BoeingDr.•Rockford,IL61109-2988USA•815-397-7070
1818 Mechanical Bender
 Y 15.00  7.30 15.02 22.75 30.48 38.21 49.80 61.39 84.57 130.94
 L1 15.00 7.72 15.44 23.17 30.90 38.63 46.35 57.94 69.54 92.72 139.08
 L2 15.00 9.71 17.43 25.16 32.89 40.62 48.34 59.93 71.52 94.71 141.07
 Z 15.00 13.42 20.88 28.34 35.81 43.27 50.74 61.93 73.13 95.52 140.30
MINIMUM H = 1.54
 Y 22.50  2.82 8.05 13.27 18.50 23.73 31.57 39.41 55.08 86.44
 L1 22.50  10.41 15.64 20.87 26.09 31.32 39.16 47.00 62.68 94.03
 L2 22.50  13.40 18.62 23.85 29.08 34.30 42.14 49.98 65.66 97.02
 Z 22.50  16.63 21.46 26.29 31.12 35.94 43.19 50.43 64.91 93.89
MINIMUM H = 2.67
 Y 30.00  0.35 4.35 8.35 12.35 16.35 22.35 28.35 40.35 64.35
 L1 30.00   11.91 15.91 19.91 23.91 29.91 35.91 47.91 71.91
 L2 30.00   15.89 19.89 23.89 27.89 33.89 39.89 51.89 75.89
 Z 30.00   18.42 21.88 25.34 28.81 34.00 39.20 49.59 70.38
MINIMUM H = 4.01
 Y 45.00   0.21 3.04 5.87 8.70 12.94 17.18 25.67 42.64
 L1 45.00    10.99 13.82 16.64 20.89 25.13 33.61 50.58
 L2 45.00    16.96 19.78 22.61 26.86 31.10 39.58 56.55
 Z 45.00    18.25 20.25 22.25 25.25 28.25 34.25 46.25
MINIMUM H = 7.25
 Y 60.00     2.25 4.56 8.02 11.49 18.42 32.27
 L1 60.00      13.04 16.50 19.97 26.90 40.75
 L2 60.00      21.00 24.46 27.93 34.85 48.71
 Z 60.00      19.65 21.39 23.12 26.58 33.51
MINIMUM H = 11.02
 Y 90.00       2.62 5.62 11.62 23.62
 L1 90.00         20.74 32.74
 L2 90.00         32.68 44.68
 Z 90.00         19.15 19.15
MINIMUM H = 19.15
 Y 15.00  5.78 13.51 21.24 28.97 36.69 48.28 59.88 83.06 129.42
 L1 15.00 7.71 15.44 23.17 30.9 38.62 46.35 57.94 69.53 92.71 139.08
 L2 15.00 10.14 17.87 25.60 33.32 41.05 48.78 60.37 71.96 95.14 141.51
 Z 15.00 14.68 22.15 29.61 37.08 44.54 52.01 63.20 74.40 96.79 141.57
MINIMUM H = 1.87
 Y 22.50  1.35 6.57 11.80 17.02 22.25 30.09 37.93 53.61 84.97
 L1 22.50  10.40 15.63 20.86 26.08 31.31 39.15 46.99 62.67 94.03
 L2 22.50  14.05 19.27 24.50 29.72 34.95 42.79 50.63 66.31 97.67
 Z 22.50  18.12 22.95 27.78 32.61 37.44 44.68 51.92 66.41 95.38
MINIMUM H = 3.2
 Y 30.00   2.84 6.84 10.84 14.84 20.84 26.84 38.84 62.84
 L1 30.00   11.89 15.89 19.89 23.89 29.89 35.89 47.89 71.89
 L2 30.00   16.74 20.74 24.74 28.74 34.74 40.74 52.74 76.74
 Z 30.00   20.14 23.60 27.07 30.53 35.73 40.92 51.32 72.10
MINIMUM H = 4.87
 Y 45.00    1.35 4.18 7.01 11.25 15.49 23.98 40.95
 L1 45.00     13.74 16.57 20.81 25.06 33.54 50.51
 L2 45.00     21.02 23.85 28.09 32.34 40.82 57.79
 Z 45.00     22.46 24.46 27.46 30.46 36.46 48.46
MINIMUM H = 8.81
 Y 60.00     0.32 2.63 6.09 9.56 16.48 30.34
 L1 60.00       16.32 19.79 26.72 40.57
 L2 60.00       26.03 29.50 36.42 50.28
 Z 60.00       24.14 25.88 29.34 36.27
MINIMUM H = 13.41
 Y 90.00        3.00 9.00 21.00
 L1 90.00         20.02 32.02
 L2 90.00         34.58 46.58
 Z 90.00         23.32 23.32
MINIMUM H = 23.32
DIM ANGLE 2" 4" 6" 8" 10" 12" 15" 18" 24" 36"
1-1/4 IMC/RIGID Dia.=1.66 Radius=7.6 X=3.95 H=Height
Special Bending Information Chart (cont’d)
1-1/2 IMC/RIGID
Dia.=1.9 Radius=9.27 X=4.78 H=Height