Thermador UCV36 - User Manual

Other manuals for Thermador UCV36

Care And Use Manual8 pages

Use And Care Manual8 pages

Installation Instructions16 pages

Questions and Answers

J
Jennifer MarksAug 19, 2025
Why Thermador UCV36 isn't working and all buttons are illuminated?
- T
  Timothy RamirezAug 19, 2025
  If nothing works and all buttons are illuminated, it might be because the intake encountered an obstruction while moving upwards and timed out. Reactivate the controls by pressing the Delay Shut Off button, followed by the Blower Off button. Then, press the Snorkel Up/Down button to continue operation. If the intake is too low to access the control buttons, reset the system by unplugging it and plugging it back in. If the problem continues, leave the intake in its current position and contact an electrician or qualified appliance service technician.
W
William AbbottAug 21, 2025
What to do if nothing works and all buttons are illuminated on my Thermador UCV36 Ventilation Hood?
- C
  Carrie KingAug 22, 2025
  If nothing works and all buttons are illuminated on your Thermador Ventilation Hood, it may be because the intake encountered an obstruction while moving up and timed out. Reactivate the controls by pressing the Delay Shut Off button, and then the Blower Off button. Press the Snorkel Up/Down button to continue operation. If the intake is so low that the control buttons are not accessible, reset the unit by unplugging it and then plugging it back in.
A
Anthony SheltonAug 25, 2025
What to do if the Thermador UCV36 Clean Filter Reminder button illuminates?
- A
  Amber SmithAug 25, 2025
  If the Clean Filter Reminder button illuminates, clean the filters. Then, press and hold the Clean Filter Reminder button for three seconds to reset the reminder.
W
Walter KelleyAug 26, 2025
How to fix Thermador Ventilation Hood if the intake stopped?
- L
  Lisa BakerAug 27, 2025
  If the intake has stopped, it may be due to an obstruction. Remove the obstruction, then press the Snor- kel Up/Down button to raise the intake. Press the button again to lower the intake.
D
Daniel RoseAug 28, 2025
What to do if the Clean Filter Reminder button illuminates on my Thermador UCV36?
- R
  Robert HarrisAug 28, 2025
  If the Clean Filter Reminder button illuminates, clean the filters. Then, press and hold the Clean Filter Reminder button for three seconds to reset the reminder.
D
david00Aug 30, 2025
What to do if Thermador UCV36 Ventilation Hood doesn't work and no buttons are illuminated?
- J
  James BennettAug 30, 2025
  If nothing works and no buttons are illuminated, the control button board might have become disconnected. Contact a qualified appliance service technician.
T
Timothy WallaceSep 1, 2025
Why is my Thermador Ventilation Hood intake stopped?
- S
  Stacy GonzalezSep 1, 2025
  The Thermador Ventilation Hood intake may be stopped due to an obstruction. Remove any obstruction, then press the Snorkel Up/Down button to raise the intake. Press the Snorkel Up/Down button again to lower the intake.
H
haasjohnSep 3, 2025
What to do if nothing works and no buttons are illuminated on my Thermador Ventilation Hood?
- S
  Sophia TorresSep 3, 2025
  If nothing works and no buttons are illuminated on your Thermador Ventilation Hood, the control button board may have become disconnected. Contact a qualified appliance service technician.
J
Jaime CarterSep 5, 2025
How to adjust the lower limit switch on a Thermador Cooktop?
- A
  Abigail CrosbySep 5, 2025
  To adjust the lower limit switch on your Thermador Cooktop: First, unplug the power cord. Then, remove the J-Box cover. Loosen the adjustment screw and raise the adjustment. Finally, tighten the adjustment screw. Note that to prevent damage to any internal parts, the snorkel should be in the raised position when this adjustment is made.
P
pcollinsSep 7, 2025
How to test the motor on a Thermador Cooktop?
- C
  Crystal Gibson MDSep 7, 2025
  To test the motor on your Thermador Cooktop, first turn off electrical power to the unit. Set the ohmmeter to the RX1 scale. Touch the test leads across the - and + terminals on the J2 pin connector of the relay board. The meter should indicate approximately 6 ohms.