Thermal Dynamics 1Torch SL60 Hand Torch User Manual

Manual 0-2962 A-13 APPENDIX
Cutting Speed Charts
NOTES
* Gas pressure shown is for torches with leads up to 25' / 7.6 m long. For 50' / 15.2 m leads, set gas
pressure to 80 psi / 5.5 bar.
5PUBMnPXSBUFJODMVEFTQMBTNBBOETFDPOEBSZHBTnPX
Air Plasma Cutting Speed Data Chart For CutMaster 100 & CutMaster 101
munimulA :lairetaM epyT001LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
Thickness TipOutput VoltsAmp erageSpeed (Per Minute) Standoff Plasma Gas PressFlow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC)(Amps)InchesMetersInchesmmpsi*bar Plasma Total**Delay (Sec)Inchesmm
0.05 1.39-8211100 80 350 8.89 0.19 4.8704.8 90 49000.19 4.8
0.1253.2 9-8211103 80 230 5.84 0.19 4.8704.8 90 49000.19 4.8
1/46.4 9-8211106 80 112 2.84 0.19 4.8704.8 90 49000.19 4.8
3/89.5 9-8211111 80 55 1.40 0.19 4.8704.8 90 49000.19 4.8
1/212.79-8211112 80 38 0.97 0.19 4.8704.8 90 49000.19 4.8
3/419.19-8211117 80 18 0.46 0.19 4.8704.8 90 490NR0.1
94
.8
125.49-8211120 80 10 0.25 0.19 4.8704.8 90 490NR0.1
94
.8
Air Plasma Cutting Speed Data Chart For CutMaster 100 & CutMaster 101
leetS dliM :lairetaM epyT001LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
Thickness TipOutput VoltsAmp erageSpeed (Per Minute) Standoff Plasma Gas PressFlow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC)(Amps)InchesMetersInchesmmpsi*bar Plasma Total**Delay (Sec)Inchesmm
0.05 1.39-8211100 80 350 8.89 0.19 4.8704.8 90 49000.19 4.8
0.1253.2 9-8211103 80 230 5.84 0.19 4.8704.8 90 49000.19 4.8
1/46.4 9-8211 10680112 2.84 0.19 4.8704.8 90 49000.19 4.8
3/89.5 9-8211111 80 55 1.40 0.19 4.8704.8 90 49000.19 4.8
1/212.79-8211112 80 38 0.97 0.19 4.8704.8 90 49000.19 4.8
3/419.19-8211117 80 18 0.46 0.19 4.8704.8 90 490NR0.1
94
.8
125.49-8211120 80 10 0.25 0.19 4.8704.8 90 490NR0.1
94
.8
Air Plasma Cutting Speed Data Chart For CutMaster 100 & CutMaster 101
leetS sselniatS :lairetaM epyT001LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
Thickness TipOutput VoltsAmp erageSpeed (Per Minute) Standoff Plasma Gas PressFlow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC)(Amps)InchesMetersInchesmmpsi*bar Plasma Total**Delay (Sec)Inchesmm
0.05 1.39-8211100 80 350 8.89 0.19 4.8704.8 90 49000.19 4.8
0.1253.2 9-8211103 80 200 5.08 0.19 4.8704.8 90 49000.19 4.8
1/46.4 9-8211 10680112 2.84 0.19 4.8704.8 90 4900.250.1
94
.8
3/89.5 9-8211111 80 55 1.40 0.19 4.8704.8 90 4900.250.1
94
.8
1/212.79-8211112 80 38 0.97 0.19 4.8704.8 90 4900.250.1
94
.8
3/419.19-8211117 80 18 0.46 0.19 4.8704.8 90 490NR0.1
94
.8
125.49-8211120 80 10 0.25 0.19 4.8704.8 90 490NR0.1
94
.8

Thermal Dynamics 1Torch SL60 Hand Torch Specifications

General

Brand	Thermal Dynamics
Model	1Torch SL60 Hand Torch
Category	Welding Accessories
Language	English